Husqvarna FE 350 2015 Repair Manual Download Page 110

Page: 110 / 308

15.3

WIRING HARNESS, BATTERY

Checkin the starter relay

Iii

Check that the power consumer is functioning properly.
Close the fuse box cover.

Finishing work

Mount the seat. (

lit!l

p. 77)

Preparatory work

Switch off all power consumers and switch off the engine.

Remove the seat. (

lit!l

p. 77)

Remove the air filter box cover. (

lit!l

p. 74)

Main work

Disconnect the negative cable from the battery.
Pull the starter relay off of the holder.

Pull off connector

Disconnect cables @ and

on the starter relay.

Connect the starter relay to a 12 V power supply as shown.

Measure the resistance between the specified points.

Resistance of open circuit

If the value displayed does not meet specifications:

Change the starter relay.

108

601201-10

Removing the battery

Warning

Risk of injury

Battery acid and battery gases cause serious chemical burns.

Keep batteries out of the reach of children.

Wear suitable protective clothing and goggles.

- Avoid contact with battery acid and battery gases.

Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms.
In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at

least 15 minutes and contact a physician.

Preparatory work

Switch off all power consumers and switch off the engine.

Remove the seat. (

�

p. 77)

Main work

Pull back the negative terminal cover

and disconnect the negative cable from

the battery.

Pull back the positive terminal cover @ and disconnect the positive cable from

the battery.

Detach rubber band

at the bottom.

Lift the battery up and out.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands