Husqvarna FE 350 2015 Repair Manual Download Page 209

Page: 209 / 308

22.1

22.2

22.3

IGNITION SYSTEM

201

Ignition coil - checking the seconds winding

601171-10

Condition

Ignition coil cylinder 1 is disconnected.

Spark plug connector cylinder 1 has been removed.

Ignition coil cylinder 1

check the secondary winding resistance

Measure the resistance between the specified points.

Ignition coil cylinder 1 pin 2 (-) - Ignition coil cylinder 1 pin 3

Ignition coil

Secondary winding resistance at:

20 °C (68 °F)

110.8 ... 16.2 kn

If the displayed value does not correspond to specifications:

- Change the ignition coil.

Checking the spark plug connector

601170-10

Condition

Spark plug connector cylinder 1 has been removed.

Measure the resistance between the specified points.

Measuring point 1 - Measuring point 2

Spark plug connector

Resistance at: 20 °c (68 °F)

If the specification is not reached:

- Change the spark plug connector.

3.75 ... 6.25 kn

Alternator - checking the stator winding

601211-10

Condition

The stator is disconnected.

Preparatory work

- Remove the seat. (

l!t!I

p. 77)

Main work

Stator winding, measurement I - check the resistance

Measure the resistance between the specified points.

Stator, connector

- Stator, connector

Alternator

Resistance of stator winding at:

20 °C (68 °F)

0.368 ... 0.552

If the value displayed does not meet specifications:

- Change the stator.

Stator winding, measurement II - check the resistance

Measure the resistance between the specified points.

Stator, connector

- Stator, connector

Alternator

Resistance of stator winding at:

20 °C (68 °F)

0.368 ... 0.552

If the value displayed does not meet specifications:

- Change the stator.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands