Husqvarna FE 350 2015 Repair Manual Download Page 30

Page: 30 / 308

FORK, TRIPLE CLAMP

Assembling the fork legs

Info

Degrease piston rod

and clamp in the vise.

Clamping stand (T14049S) (

@}J

p. 299)

Screw spring guide Ci) all the way on.

•

Info

The nut must be firmly tightened against the stop by hand. Do not use a

tool.

Mount adjusting tube

4'.

Unclamp the piston rod. Mount the preload spacer(s).

When assembling, ensure that the right cartridge is mounted in the corresponding inner tube and the right adjuster is

mounted on the corresponding screw cap.

Compression damping side - screw cap with mark

COMP,

brake caliper holder, white adjuster.

Rebound damping side - screw cap with mark

REB,

no brake caliper holder, red adjuster.

-8

201714-10

Preparatory work

Assemble the hydrostop unit. (

ll!ll

p. 25)

Main work

Clamp the inner tube with the axle clamp.
Guideline

Use soft jaws.

Mount special tool.

Protecting sleeve (T1401) (

@}J

p. 298)

Lubricate and mount dust boot

Lubricant (T511) (

p. 286)

•

Info

Always change the dust boot, seal ring, lock ring and support ring.

Mount the sealing lip with the spring expander facing downward.

Slide on lock ring @.

Lubricate and slide on seal ring

@).

Lubricant (T511) (

@}J

p. 286)

•

Info

Mount with the sealing lip facing down and the open side facing up.

Slide on support ring

Remove the special tool.

Grind the edges of the sliding bushings with sandpaper grit 600, clean the bush-

ings and lubricate them.

Fork oil (SAE 4) (48601166S1) (

ll!ll

p. 284)

201715-10

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands