Husqvarna FE 350 2015 Repair Manual Download Page 197

Page: 197 / 308

18 ENGINE

18.5.34 Installing the spacer

18.5.35 Installing the clutch push rod

- Push the oil screen with O-rings onto a pin wrench.

195

- Push the pin wrench through the opening into the drill hole of the opposite engine

case wall and push the oil screen as far as possible into the engine case.

- Mount and tighten screw plug

with the O-ring.

Guideline

Screw plug, oil screen

M20x1.5

- Grease the shaft seal ring before mounting.

I1 s Nm (11.1 lbf ft)

- Position the O-ring. Mount spacer

with the bevel facing inward.

- Mount clutch push rod

18.5.36 Removing the engine from the engine assembly stand

- Remove the screw connection from the special tool.

Engine fixing arm (77229002000) (

p. 293)

- Remove the engine from the engine assembly stand.

Info

Work with an assistant or a motorized hoist.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands