manualshive.com logo in svg

Husqvarna FE 350 2015, Repair Manual

The Husqvarna FE 350 2015 Repair Manual is a comprehensive guide that allows you to easily maintain and repair your motorcycle. This user-friendly manual provides step-by-step instructions, diagrams, and troubleshooting tips. Download it for free from our website and keep your bike in top condition for optimal performance and longevity.

Share
Download
background image

INDEX 

'A 

'Accessories 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8 

'Activated charcoal filter 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  86 

'Activated charcoal filter 

removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  85 

'Air filter 

cleaning 
installing 
removing 

.................................  75 
.................................  74 

74 

'Air filter box 

cleaning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75 
sealing  ..................................  75 

'Air filter box cover 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7 4 
removing 

74 

'Alternator 

stator winding,  checking 

207 

'Antifreeze 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  199 

'Auxiliary substances 

. . . . . . . . . . . . . . . . . . . . . . . . . . .  8 

B 

Battery 

installing 

109 
109 
108 

recharging 
removing 

Brake disc 

front brake,  installing  . . . . . . . . . . . . . . . . . . . . . . . .  95 
front brake,  removing  . . . . . . . . . . . . . . . . . . . . . . . .  94 
rear brake, installing  .........................  98 
rear brake,  removing  . . . . . . . . . . . . . . . . . . . . . . . .  98 

Brake discs 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  92 

Brake fluid 

front brake,  changing 
of front brake,  adding 
of rear brake, adding 
rear brake,  changing 

116 
115 
122 
123 

Brake fluid level 

front brake,  checking 

114 

rear brake,  checking . . . . . . . . . . . . . . . . . . . . . . . .  121 

Brake linings 

C 

front brake,  changing 
front brake,  checking 

111 
111 

of rear brake,  changing  . . . . . . . . . . . . . . . . . . . . . .  119 
rear brake,  checking . . . . . . . . . . . . . . . . . . . . . . . .  118 

Capacity 

coolant  .............................. 201,  214 
engine oil  ........................  137,  204,  214 
fuel  ...................................  214 

Cartridge 

fork legs,  assembling  . . . . . . . . . . . . . . . . . . . . . . . .  27 
fork legs,  disassembling  . . . . . . . . . . . . . . . . . . . . . .  20 

301 

Chain 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99 
cleaning 

Chain guide 

101 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99 

Chain tension 

adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99 

checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  98 

Charging voltage 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  110 

Chassis number 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9 

Closed current 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  110 

Clutch 

fluid level, checking/correcting  . . . . . . . . . . . . . . . .  196 
fluid,  changing  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  197 

Clutch lever 

basic position,  adjusting  . . . . . . . . . . . . . . . . . . . . . .  38 

Compression  damping 

fork,  adjusting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13 

Compression damping, high-speed 

shock absorber,  adjusting  . . . . . . . . . . . . . . . . . . . . .  42 

Compression damping, low-speed 

shock absorber,  adjusting  . . . . . . . . . . . . . . . . . . . . .  42 

Coolant 

antifreeze and coolant level, checking 

199 

draining  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  200 
level,  checking ............................  200 
refilling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  201 

Cooling system 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  199 

Cylinder - Nikasil

® 

coating 

. . . . . . . . . . . . . . . . . . . . .  159 

D 

Drivetrain kit 

E 

changing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  102 

Engine 

installing 
removing 

133 
129 

Engine - work on individual parts 

cam levers, checking  . . . . . . . . . . . . . . . . . . . . . . .  164 
camshaft bearing, changing  . . . . . . . . . . . . . . . . . .  161 
camshafts,  checking 

162 

clutch cover  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  153 
clutch, checking  . . . . . . . . . . . . . . . . . . . . . . . . . .  170 
connecting rod, conrod bearing and crank pin, changing 156 
countershaft,  assembling  . . . . . . . . . . . . . . . . . . . .  176 
countershaft,  disassembling  . . . . . . . . . . . . . . . . . .  173 

crankshaft bearing inner race,  installing 

156 

crankshaft bearing inner race,  removing  . . . . . . . . . .  156 

crankshaft end play,  measuring  . . . . . . . . . . . . . . . .  158 
crankshaft  run-out,  checking at bearing pin  . . . . . . . .  158 

cylinder -

Nikasil

® 

coating  . . . . . . . . . . . . . . . . . . .  159 

cylinder head,  checking  . . . . . . . . . . . . . . . . . . . . .  165 

cylinder,  checking/measuring  . . . . . . . . . . . . . . . . .  159 

drive wheel of balancer shaft,  removing  . . . . . . . . . .  158 

Summary of Contents for FE 350 2015





















































































































































































































































































































Reviews:

No comments

Related manuals for FE 350 2015

X-lite CLEO Installation Instructions preview
CLEO
Brand: X-lite Pages: 5
Öhlins McPherson Strut MIR 1G00 Mounting Instructions preview
McPherson Strut MIR 1G00
Brand: Öhlins Pages: 2
Öhlins BM 543 Mounting Instruction preview
BM 543
Brand: Öhlins Pages: 2
Öhlins BM 503 Mounting Instructions preview
BM 503
Brand: Öhlins Pages: 2
Würth 0984 700 400 Manual preview
0984 700 400
Brand: Würth Pages: 188
DMC 25470-00 Installation Instructions preview
25470-00
Brand: DMC Pages: 2
STEEL HORSE AUDIO ST400 Cruiser Edition Installation Instructions Manual preview
ST400 Cruiser Edition
Brand: STEEL HORSE AUDIO Pages: 6
hepco & becker 6609516 01 01 Quick Start Manual preview
6609516 01 01
Brand: hepco & becker Pages: 4
Memphis Shades 2320-0076 Mounting Instructions preview
2320-0076
Brand: Memphis Shades Pages: 2
Suzuki 990D0-28K50-CLE Installation Instructions Manual preview
990D0-28K50-CLE
Brand: Suzuki Pages: 12
Crivit 271528 Instructions For Use Manual preview
271528
Brand: Crivit Pages: 30
LSL 121B029 Fitting Instruction preview
121B029
Brand: LSL Pages: 12
Yamaha MT-07 2021 Owner'S Manual preview
MT-07 2021
Brand: Yamaha Pages: 108
Yamaha MT-09 2023 Owner'S Manual preview
MT-09 2023
Brand: Yamaha Pages: 118
Yamaha MT-07M 2015 Owner'S Manual preview
MT-07M 2015
Brand: Yamaha Pages: 110
Yamaha MT-10 2020 Owner'S Manual preview
MT-10 2020
Brand: Yamaha Pages: 120
Yamaha SRX600 1997 Service Manual preview
SRX600 1997
Brand: Yamaha Pages: 216
Yamaha MBK MW125 2014 Service Manual preview
MBK MW125 2014
Brand: Yamaha Pages: 380

Brands by name

Popular brands

Load more brands