Husqvarna FE 350 2015 Repair Manual Download Page 81

Page: 81 / 308

12.8

FUEL TANK, SEAT, TRIM

Installing the fuel tank

Danger
Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

- Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

- Switch off the engine for refueling.

- Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

- If any fuel is spilled, wipe it off immediately.

- Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.

- Immediately consult a doctor if you swallow fuel.

- Do not inhale fuel vapors.

- In case of skin contact, rinse the affected area with plenty of water.

- Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

- Change your clothing in case of fuel spills on them.

Main work

- Check the routing of the throttle cable. (

�

p. 39)

- Position the fuel tank and fit the two spoilers to the sides of the radiator bracket.

- Make sure that no cables are trapped or damaged.

- Mount the fuel tank breather.

- Mount and tighten screw

with the rubber bushing.

Guideline

Remaining screws, chassis

I 10Nm(7.41bf ft)

- Position the collar bushings and horn, fit and tighten screws

Guideline

Remaining screws, chassis

- Attach the connector of the horn.

- Attach connector

of the fuel pump.

- Remove the wash cap set.

10 Nm (7.4 lbf ft)

- Thoroughly clean the plug-in connection of the fuel line using compressed air.

•

Info

Never let dirt enter the fuel line. Dirt in the fuel line clogs the injection

valve.

- Lubricate the O-ring and connect plug-in connection

of the fuel line.

•

Info

Route the cable and fuel line at a safe distance from the exhaust system.

Finishing work

- Mount the seat. (

�

p. 77)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands