manualshive.com logo in svg

Husqvarna FE 350 2015, Repair Manual

The Husqvarna FE 350 2015 Repair Manual is a comprehensive guide that allows you to easily maintain and repair your motorcycle. This user-friendly manual provides step-by-step instructions, diagrams, and troubleshooting tips. Download it for free from our website and keep your bike in top condition for optimal performance and longevity.

Share
Download
background image

INDEX 

Foot brake lever 

basic position,  adjusting 
free travel,  checking 

121 
120 

Fork legs 

assembling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28 
bleeding  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13 
cartridge,  assembling  . . . . . . . . . . . . . . . . . . . . . . . .  27 

cartridge, disassembling  . . . . . . . . . . . . . . . . . . . . . .  20 
checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23 
disassembling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17 

dust boots,  cleaning  . . . . . . . . . . . . . . . . . . . . . . . . .  14 
fork service,  performing  . . . . . . . . . . . . . . . . . . . . . .  17 
hydrostop unit,  assembling  . . . . . . . . . . . . . . . . . . . .  25 
hydrostop unit, disassembling  . . . . . . . . . . . . . . . . . .  22 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15 

piston rod,  assembling  . . . . . . . . . . . . . . . . . . . . . . .  25 

piston rod, disassembling  . . . . . . . . . . . . . . . . . . . . .  21 

removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15 

seal ring retainer,  assembling  ..................  24 
seal ring retainer, disassembling  . . . . . . . . . . . . . . . .  23 
spring,  removing  . . . . . . . . . . . . . . . . . . . . . . . . . . .  19 

Fork protector 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17 
loosening  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14 
removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16 

Fork service, performing 

. . . . . . . . . . . . . . . . . . . . . . .  17 

Frame 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41 

Front fender 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  87 

removing 

Front wheel 

................................  87 

installing 
removing 

.................................  94 

93 

Fuel filter 

changing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80 

Fuel pressure 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  84 

Fuel pump 

changing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82 

Fuel screen 

changing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80 

Fuel tank 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  79 
removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77 

Fuse 

H 

individual power consumers,  changing  . . . . . . . . . . .  106 
main fuse,  changing  . . . . . . . . . . . . . . . . . . . . . . . .  106 

Hand brake lever 

basic position,  adjusting 
free travel,  adjusting 

114 
114 

free travel,  checking  . . . . . . . . . . . . . . . . . . . . . . . .  113 

Handlebar position 

. . . . . . . . . . . . . . . . . . . . . . . . . . .  38 

adjusting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38 

303 

Headlight 

light range,  adjusting 

128 

Headlight adjustment 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  127 

Headlight mask with headlight 

installing  .................................  89 
removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  88 

Hydrostop unit 

fork legs,  assembling  . . . . . . . . . . . . . . . . . . . . . . . .  25 
fork legs, disassembling  . . . . . . . . . . . . . . . . . . . . . .  22 

Idle speed 

adjusting 

211 

Ignition coil 

secondary winding,  checking 

207 

Implied warranty 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8 

Initialization run 

executing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  211 

K 

Key number 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9 

L 

Lower triple clamp 

installing  .................................  33 
removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32 

M 

Main fuse 

changing 

106 

Main silencer 

changing the glass fiber yarn filling . . . . . . . . . . . . . . .  71 

installing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71 

removing  ................................  71 
spark arrestor, cleaning 

73 

Manifold 

installing  .................................  69 

removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  68 

Motor sprocket 

checking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99 

Motorcycle 

0 

cleaning  ................................  219 
raising with lift stand  . . . . . . . . . . . . . . . . . . . . . . . .  11 
removing from lift stand  . . . . . . . . . . . . . . . . . . . . . .  11 

Oil circuit 
Oil filter 

changing 

202 

203 

Oil screen 

cleaning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  203 

Operating substances 

. . . . . . . . . . . . . . . . . . . . . . . . . .  8 

p 

Piston rod 

fork legs,  assembling  . . . . . . . . . . . . . . . . . . . . . . . .  25 
fork legs, disassembling  . . . . . . . . . . . . . . . . . . . . . .  21 

Summary of Contents for FE 350 2015





















































































































































































































































































































Reviews:

No comments

Related manuals for FE 350 2015

Maico MC 400 Service Bulletin preview
MC 400
Brand: Maico Pages: 13
DAELIM ROADWIN 125 FI Manual preview
ROADWIN 125 FI
Brand: DAELIM Pages: 68
hepco & becker 6513515 00 22-00-40 Manual preview
6513515 00 22-00-40
Brand: hepco & becker Pages: 7
rizoma BS232 User Manual preview
BS232
Brand: rizoma Pages: 16
PIAGGIO NRG 50 User Manual preview
NRG 50
Brand: PIAGGIO Pages: 275
ICON Vehicle Dynamics 57823P Installation Instructions preview
57823P
Brand: ICON Vehicle Dynamics Pages: 4
BMW R 1200 R Classic Technical Data preview
R 1200 R Classic
Brand: BMW Pages: 1
OKBABY Ladybug N.39030000 Instructions Manual preview
Ladybug N.39030000
Brand: OKBABY Pages: 13
SHARKS Devil Instruction For Operation And Maintenance preview
Devil
Brand: SHARKS Pages: 25
APRILIA RST FUTURA - 2001 Dealer Instructions preview
RST FUTURA - 2001
Brand: APRILIA Pages: 2
Baja PX250 Setup Instructions preview
PX250
Brand: Baja Pages: 8
APRILIA RSV MILLE SPORT - PART 2 1999 Manual preview
RSV MILLE SPORT - PART 2 1999
Brand: APRILIA Pages: 47
APRILIA RS 125 TUONO Manual preview
RS 125 TUONO
Brand: APRILIA Pages: 288
APRILIA Pegaso 650 I.E. Service Manual preview
Pegaso 650 I.E.
Brand: APRILIA Pages: 320
hepco & becker 710081 Assembly preview
710081
Brand: hepco & becker Pages: 2
Royal Enfield Bullet 350 2019 Owner'S Manual preview
Bullet 350 2019
Brand: Royal Enfield Pages: 68
TAYO ZONTES 310T-M 2022 Maintenance Manual preview
ZONTES 310T-M 2022
Brand: TAYO Pages: 188
Baja motorsports DR70 Operator'S Manual preview
DR70
Brand: Baja motorsports Pages: 48

Brands by name

Popular brands

Load more brands