Husqvarna FE 350 2015 Repair Manual Download Page 165

Page: 165 / 308

18 ENGINE

18.4.21 Removing the valves

l//

:E-V1

•

302712-10

300117-10

Take off the camshafts and clean the parts.

Remove screw plugs

with the O-ring.

Screw appropriate screw

into the cam lever shaft.

Hold cam levers

and remove the cam lever shaft.

•

Info

163

If the cam levers will continue to be used, note down their installation posi

tion.

Take the shims out of the valve spring retainers and lay them to one side accord

ing to their normal built-in position.

Pre-tension the valve spring using the special tool.

Valve spring mounter (59029019000) (

lllll

p. 290)

Insert for valve spring lever (77229060000) (

�

p. 295)

Remove the valve keys and unload the valve spring.

Remove the valve spring retainer and valve springs.

Pull the valve down out of the valve guide.

Remove valve stem seal

with the special tool.

Pliers for valve stem seals (77229010000) (

�

p. 293)

Remove valve spring seat

Mark the valves according to their normal built-in position.

•

Info

Place the valves into a box according to the installation position and label

the box .

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands