Husqvarna FE 350 2015 Repair Manual Download Page 164

Page: 164 / 308

18 ENGINE

18.4.19 Checking the camshafts

308667-10

Check the camshaft for damage and wear.

If there is damage or wear:

Change the camshaft.

If the surface of the cams is damaged, check the oil supply to the

camshaft and cam lever.

Check the autodecompressor for damage and wear.

If there is damage or wear:

Change the exhaust camshaft.

Slide the camshaft bearing to the camshaft gear.

Pull lever

away from camshaft and release it.

If the lever does not return to its original position:

Change the exhaust camshaft.

162

18.4.20 Checking the pivot points of the camshafts

308668-10

Check the pivot points of the camshafts.

If there is damage or wear:

Change the cylinder head with the camshaft bearing bridge.

Position the camshafts.

✓ The valves are not activated.

Insert the

Plastigauge

clearance gauge in area

Plastigauge

clearance gauge (60029012000) (

�

p. 291)

Position camshaft bearing bridge

Mount and tighten the screws.

Guideline

Screw, camshaft bearing

bridge

•

Info

M7x1

14 Nm

(10.3 lbf ft)

Lubricated with

engine oil

Ensure that the dowel pins are seated properly.

Do not turn the camshaft.

Remove camshaft bearing bridge

again. Compare the

Plastigauge

clearance

gauge with the specifications on the packaging.

Guideline

Camshaft bearing - sleeve bearing

Radial clearance

0.020 ... 0.054 mm (0.00079 ...

0.00213 in)

Wear limit

0.065 mm (0.00256 in)

Info

The width of the

Plastigauge

clearance gauge is a measure of the bearing

play.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands