Husqvarna FE 350 2015 Repair Manual Download Page 161

Page: 161 / 308

18 ENGINE

159

18.4.12 Installing the drive wheel of the balancer shaft

303077-10

18.4.13 Cylinder - Nikasil

coating

302699-10

- Ensure that woodruff key

is seated properly.

- Warm drive wheel @ of the balancer shaft and push it onto the balancer shaft.

Guideline

1100 °C (212 °F)

Nikasil

is a surface protection layer for a coating procedure developed by Mahle.

The name is derived from the two materials used in this procedure - a layer of nickel

into which is embedded the particularly hard silicone carbide.

The most important advantages of the

Nikasil

coating are very good heat conduc

tivity, resulting in much improved performance, low wear, and a lightweight cylinder.

18.4.14 Checking/measuring the cylinder

'--

305004-10

- Check the cylinder bearing surface for damage.

If the cylinder bearing surface is damaged:

- Change the cylinder and piston.

- Measure the cylinder diameter at several locations on the

and

0-axes

using

a micrometer to identify oval wear.

Guideline

Cylinder - drill hole diameter

Size I

Size II

•

Info

88.000 ... 88.012 mm (3.46456 ...

3.46503 in)
88.012 ... 88.025 mm (3.46503 ...

3.46554 in)

The cylinder size

is marked on the cylinder collar.

- Using a straightedge and the special tool, check the sealing area of the cylinder

head for distortion.

Feeler gauge (59029041100) (

�

p. 291)

Cylinder/cylinder head - distortion of

sealing area

s; 0.10 mm (::. 0.0039 in)

If the measured value does not meet specifications:

- Change the cylinder.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands