Husqvarna FE 350 2015 Repair Manual Download Page 27

Page: 27 / 308

FORK, TRIPLE CLAMP

Assembling the h

Info

The steps are identical for both fork legs.

201975-10

Assembling the �iston rod

Info

- Mount and grease O-ring

Lubricant (T158) (

�

p. 286)

- Mount washer

- Mount shim stack

with the smaller washers facing downward.

- Mount the new O-ring on hub

C,.

- Mount the hub with washers

C,.

•

Info

It is possible that only one or no washer is present.

- Mount and tighten adapter

(D.

Guideline

Hydrostop unit adapter

M6x0.5

I 7 Nm (5.2 lbf ft)

- Mount shim stack @ with the smaller washers facing downward.

- Mount and tighten sleeve

@).

Guideline

Hydrostop unit sleeve

M6x0.5

- Check distance

and total length

of the hydrostop.

Guideline

I 7 Nm (5.2 lbf ft)

Hydrostop distance

� 1.5 mm (� 0.059 in)

Hydrostop length

» If the dimensions are out of tolerance:

- Add or remove washers

108.5 ... 109.5 mm (4.272 ... 4.311 in)

The steps are identical for both fork legs, except for the hydrostop needle and valve.

- Degrease the piston rod.

- Clamp the piston rod with the special tool.

Clamping stand (T14049S) (

p. 299)

- Lubricate the O-ring. Mount valve needle

in the piston rod.

Lubricant (T158) (

p. 286)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands