Husqvarna FE 350 2015 Repair Manual Download Page 159

Page: 159 / 308

18 ENGINE

302912-10

308662-10

Press the crank pin out of the lower crank web.

Press in the new crank pin

as far as possible.

✓ Oil hole

is aligned with oil hole@).

157

X If the oil holes are not correctly aligned, the conrod bearing will not be sup

plied with oil.

Blow compressed air through the oil channel to check that it is clear.

Mount the new connecting rod

C,.

Info

Thoroughly oil the bearing

@).

Position special tool (3 on the press.

Pressing tool for crankshaft, complete (75029047000) (

p. 292)

Insert for crankshaft pressing tool (77229008000) (

!!;!I

p. 293)

Insert the crank web with connecting rod and bearing. Position the second crank

web.

Position special tool @ with the heel pointing down.

Insert for crankshaft pressing tool (77229008000) (

p. 293)

Press in the upper crank web as far as possible.

•

Info

The press mandrel must be positioned over the crank pin.

Take the crankshaft out of the special tool and check that the connecting rod can

move freely.

Measure the axial play between the connecting rod and the crank webs with spe

cial tool

@).

Feeler gauge (59029041100) (

!.;!I

p. 291)

Connecting rod - axial play of lower

conrod bearing

If the specification is not reached:

0.20 ... 0.45 mm (0.0079 ... 0.0177 in)

Correct it so the dimension is equal to the specified value.

Finishing work

Check the crankshaft run-out at the bearing pin. (

p. 158)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands