Husqvarna FE 350 2015 Repair Manual Download Page 139

Page: 139 / 308

18 ENGINE

18.3

Engine disassembl

18.3.1

Preparations

- Connect negative cable � of the battery.

Guideline

Screw, battery terminal

•

Info

2.5 Nm

(1.84 lbf ft)

137

The contact disk

must be mounted between the battery terminal and

cable lug with the claws facing up.

- Refill the coolant. (

il,)

p. 201)

- Install the main silencer. (

il,)

p. 71)

- Install the right side cover. (

il,)

p. 77)

- Remove the motorcycle from the lift stand. (

p. 11)

(FE 350S US)

- Install the activated charcoal filter. (

p. 86)

- Install the fuel tank. (

p. 79)

- Mount the seat. (

p. 77)

(FE EU/ AU/US)

- Install the fuel tank. (

p. 79)

- Mount the seat. (

p. 77)

- Remove screw cap � on the clutch cover and fill in engine oil.

Engine oil

11.20 I (1.27 qt.)

Engine oil (SAE 1 0W/50) (

p. 284)

- Mount and tighten fitting �-

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and death.

- Always make sure there is sufficient ventilation when running the

engine.

- Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

- Start the engine and check that it is oil-tight.

- Switch off the engine.

- Check the engine oil level. (

�

p. 202)

- Check the coolant level. (

�

p. 200)

- Execute the initialization run. (

�

p. 211)

Finishing work

- Take a test ride.

- Read out the fault memory using the Husqvarna Motorcycles diagnostics tool.

- Check the engine for leak tightness.

- Check the engine oil level. (

p. 202)

- Check the coolant level. (

p. 200)

- Install the engine guard. (

p. 41)

- Mount the special tool on the engine mounting block.

Engine fixing arm (77229002000) (

p. 293)

Engine assembly stand (61229001000) (

�

p. 292)

Mount the engine on the special tool.

Info

Work with an assistant or a motorized hoist.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands