Husqvarna FE 350 2015 Repair Manual Download Page 35

Page: 35 / 308

6.26

FORK, TRIPLE CLAMP

Installing the lower tri

�

I...:

-tt,1...t

;:;:;,;

0- -8

Main work

Clean the bearing and sealing elements, check for damage, and grease.

High viscosity grease (

il!.!J

p. 286)

Position the lower triple clamp with the steering stem. Mount the upper steering

head bearing.

Check whether the upper steering head seal

is correctly positioned.

Mount protective ring

and 0-ring (D.

Position the upper triple clamp with the handlebar.

Mount screw

but do not tighten yet.

Position the clutch line in the guide above the voltage regulator.

Position the fork legs.

✓ Bleeder screws

are positioned toward the front.

•

Info

The compression damping is located in the left fork leg

COMP

(white

adjusting screw). The rebound damping is located in the right fork leg REB

(red adjusting screw).

Grooves are milled into the side of the upper end of the fork legs. The sec

ond milled groove (from the top) must be flush with the top edge of the

upper triple clamp.

(FE EU/ AU/US)

- Tighten screws

(D.

Guideline

Screw, bottom triple clamp

15 Nm

(1 U lbf ft)

(FE 350S US)

- Tighten screws

(D.

Guideline

Screw, bottom triple clamp

15 Nm

(1 U lbf ft)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands