Husqvarna FE 350 2015 Repair Manual Download Page 119

Page: 119 / 308

BRAKE SYSTEM

>------400379-10

G02092-10

G02093-10

Open shut-off valve

•

Info

Follow the operating instructions of the bleeding device.

117

Ensure that the filling pressure is set on pressure gauge t). Correct the filling

pressure on pressure regulator

if necessary.

Guideline

Filling pressure

2 ... 2.5 bar (29 ... 36 psi)

Pull off protection cap

of the brake caliper bleeder screw. Connect the

bleeder bottle hose.

Bleeding device (00029013100) (

!lll

p. 288)

Open bleeder screw Q) by approx. one half turn.

•

Info

Drain until fresh brake fluid emerges in the bleeder bottle hose without

bubbles.

Tighten the bleeder screw.

Close shut-off valve

Open the bleeder screw again until brake fluid stops emerging.

•

Info

Overfilling of the brake fluid reservoir is prevented.

Tighten the bleeder screw. Remove the bleeder bottle hose. Mount the pro

tection cap.

Disconnect the bleeding device. Remove the bleeder cover.

Correct the brake fluid to level Q).
Guideline

Level Q)

Brake fluid DOT 4 (

�

p. 284)

5 mm (0.2 in)

Position the cover with the membrane. Mount and tighten the screws.

•

Info

Clean up overflowed or spilled brake fluid immediately with water.

Check the hand brake lever for a firm pressure point.

(FE 350S US)

Move the brake fluid reservoir mounted on the handlebar to a horizontal posi-

tion.

Cover painted parts.

Remove screws

Remove cover @ with the membrane.

Draw the old brake fluid out of the brake fluid reservoir using a syringe and fill

with fresh brake fluid.

Bleed syringe (50329050000) (

p. 289)

Brake fluid DOT 4 (

�

p. 284)

Mount bleeder cover

Bleeder cover (00029013005) (

�

p. 288)

Connect the bleeding device.

Bleeding device (00029013100) (

p. 288)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands