Husqvarna FE 350 2015 Repair Manual Download Page 42

Page: 42 / 308

7.6

HANDLEBAR,CONTROLS

Danger
Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and death.
- Always make sure there is sufficient ventilation when running the

engine.

Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

Start the engine and let it run idle. Move the handlebar to and fro over the entire

steering range.

The idle speed must not change.

If the idle speed changes:

- Adjust the play in the throttle cable. (

�

p. 40)

Ad"usting the la in the throttle cable

Preparatory work

Remove the seat. (

Ill;!

p. 77)

Remove the fuel tank. (

Ill;!

p. 77)

Check the routing of the throttle cable. (

�

p. 39)

Main work

Move the handlebar to the straight-ahead position.

Push back sleeves

Loosen nut @. Turn adjusting screw

in as far as possible.

Loosen nut

Turn adjusting screw

so that there is play

in the throttle

cable at the throttle grip.

Guideline

Play in throttle cable

13 ...

5 mm (0.12 ... 0.2 in)

Tighten nut

Press and hold the throttle grip in the closed setting. Turn adjusting screw

out

until there is no play in throttle cable Q).

Tighten nut

Push sleeves

on. Check the throttle grip for smooth operation.

Finishing work

Install the fuel tank. (

�

p. 79)

Mount the seat. (

�

p. 77)

Check the play in the throttle cable. (

�

p. 39)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands