manualshive.com logo in svg

Husqvarna FE 350 2015, Repair Manual

The Husqvarna FE 350 2015 Repair Manual is a comprehensive guide that allows you to easily maintain and repair your motorcycle. This user-friendly manual provides step-by-step instructions, diagrams, and troubleshooting tips. Download it for free from our website and keep your bike in top condition for optimal performance and longevity.

Share
Download
background image

12 

12.9 

m 

A 

FUEL TANK, SEAT, TRIM 

Changing the fuel screen 

Danger 
Fire hazard 

Fuel is highly flammable. 

The fuel in the fuel tank expands when warm and can escape if overfilled. 

-

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

-

Switch off the engine for refueling.

-

Make sure that no fuel is spilled;  particularly not on hot parts of the vehicle.

-

If any fuel is spilled,  wipe it off immediately.

-

Observe the specifications for refueling.

Warning 

Danger of poisoning 

Fuel is poisonous and a health hazard. 

- Avoid skin,  eye and clothing contact with fuel.
-

Immediately consult a doctor if you swallow fuel.

-

Do not inhale fuel vapors.

-

In case of skin contact,  rinse the affected area with plenty of water.

-

Rinse the eyes thoroughly with water,  and consult a doctor in case of fuel contact with the eyes.

-

Change your clothing in case of fuel spills on them.

Warning 

Environmental  hazard 

Improper handling of fuel is a danger to the environment. 

-

Do not allow fuel to enter the groundwater,  the soil,  or the sewage system.

-

Clean plug-in connection 

O 

of the fuel line thoroughly with compressed air.

• 

Info

80 

I 

Under no circumstances should dirt enter into the fuel line.  Dirt in the fuel 

line clogs the injection valve! 

-

Disconnect the plug-in connection of the fuel line.

• 

Info

I 

Remaining fuel may flow out of the fuel hose. 

-

Pull fuel screen 

8 

out of the connecting piece.

-

Insert the new fuel screen all the way into the connecting piece.

-

Lubricate the O-ring and connect plug-in connection of the fuel line.

m

Danger 
Danger of poisoning 

Exhaust gases are toxic and inhaling them may 

result in unconsciousness and death. 

- Always make sure there is sufficient ventilation when running the 

engine. 

-

Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

-

Start the engine and check the response.

12.10  Changing the fuel filter 

m

Danger 
Fire hazard 

Fuel is highly flammable. 

The fuel in the fuel tank expands when warm and can escape if overfilled. 

-

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

-

Switch off the engine for refueling.

-

Make sure that no fuel is spilled;  particularly not on hot parts of the vehicle.

-

If any fuel is spilled,  wipe it off immediately.

-

Observe the specifications for refueling.

Summary of Contents for FE 350 2015





















































































































































































































































































































Reviews:

No comments

Related manuals for FE 350 2015

LAZER Century User Manual preview
Century
Brand: LAZER Pages: 6
Qingqi QM110GY Owner'S Manual preview
QM110GY
Brand: Qingqi Pages: 48
KEEWAY RKV125 Instruction And Maintenance Manual preview
RKV125
Brand: KEEWAY Pages: 164
hepco & becker 653999 00 01 Manual preview
653999 00 01
Brand: hepco & becker Pages: 5
R&G SS0059 Fitting Instructions Manual preview
SS0059
Brand: R&G Pages: 6
rizoma BS211 User Manual preview
BS211
Brand: rizoma Pages: 14
Androware YC-06-C User Manual preview
YC-06-C
Brand: Androware Pages: 2
N-Com SPCOM00000109 Quick Start Manual preview
SPCOM00000109
Brand: N-Com Pages: 2
DYNATEK D33-1 Installation Instructions preview
D33-1
Brand: DYNATEK Pages: 4
DYNATEK 1003007FONTANASPRINT Installation & User Manual preview
1003007FONTANASPRINT
Brand: DYNATEK Pages: 7
Aim MXK10 User Manual preview
MXK10
Brand: Aim Pages: 47
Wunderkind Custom 106503-F15 Installation And Safety preview
106503-F15
Brand: Wunderkind Custom Pages: 16
Malaguti SPIDER MAX GT 500 Service Manual preview
SPIDER MAX GT 500
Brand: Malaguti Pages: 104
Malaguti GRIZZLY Owner'S Manual preview
GRIZZLY
Brand: Malaguti Pages: 172
hepco & becker 8004564 00 01 Quick Manual preview
8004564 00 01
Brand: hepco & becker Pages: 3
KTM 250 EXC-F EU Setup Instructions preview
250 EXC-F EU
Brand: KTM Pages: 14
Rivco CA400C Installation Instructions preview
CA400C
Brand: Rivco Pages: 2
Vinz Fiori Instruction Manual preview
Fiori
Brand: Vinz Pages: 23

Brands by name

Popular brands

Load more brands