Husqvarna FE 350 2015 Repair Manual Download Page 203

Page: 203 / 308

WATER PUMP, COOLING SYSTEM

Refillin coolant

Warning

(FE EU/ AU/US)

- Position the motorcycle upright.

- Place a suitable container under the water pump cover.

- Remove screw

Take off radiator cap

- Completely drain the coolant.

- Mount and tighten screw

with a new seal ring.

Guideline

Screw, water pump cover

(FE 350S US)

- Position the motorcycle upright.

- Place a suitable container under the water pump cover.

- Remove screw

Take off radiator cap

- Completely drain the coolant.

- Mount and tighten screw

with a new seal ring.

Guideline

Screw, water pump cover

Danger of poisoning

Coolant is toxic and a health hazard.

- Keep coolant out of the reach of children.

- Do not allow coolant to come into contact with the skin, the eyes and clothing.

- Consult a doctor immediately if coolant is swallowed.

- Rinse the affected area immediately with plenty of water in the event of contact with the skin.

- Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

- Change clothing if coolant spills onto your clothing.

Main work

- Make sure that the screw

is tightened.

- Stand the vehicle upright.

201

110 Nm (7.4 lbf ft)

I 10Nm(7.41bf ft)

- Pour coolant in up to measurement

above the radiator fins.

Guideline

110 mm (0.39 in)

Coolant

11.2 I (1.3 qt.)

- Refit the radiator cap.

Finishing work

- Take a short test ride.

- Check the coolant level. (

�

p. 200)

Coolant (

p. 284)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands