Husqvarna FE 350 2015 Repair Manual Download Page 178

Page: 178 / 308

18 ENGINE

Mount needle bearing

Mount 6th-gear idler gear @.

Mount stop disk

and lock ring

Mount 3rd/4th-gear sliding gear

with the small gear wheel facing downward.

Mount lock ring (3.

Mount stop disk@.

Mount needle bearing (D.

Mount 5th-gear idler gear

Mount 2nd-gear fixed gear

and stop disk

G,.

Finally, check all gear wheels for smooth operation.

18.4.41 Assembling the countershaft

Info

Use new lock rings with every repair.

Preparatory work

Carefully lubricate all parts before assembling.

Check the transmission. (

!i.,!I

p. 174)

Main work

Fix the countershaft in the vice with the toothed end facing downward.

Guideline

Use soft jaws

Mount needle bearing

Mount 2nd-gear idler gear@.

Mount stop disk

and lock ring

Mount 5th-gear sliding gear

with the shift groove facing up.

Mount lock ring (3 and stop disk @.

Mount needle bearing (D.

Mount 4th-gear idler gear

Mount needle bearing

CD.

Mount 3rd-gear idler gear

G,.

Mount lock ring

and stop disk 41).

305012-11

176

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands