Husqvarna FE 350 2015 Repair Manual Download Page 85

Page: 85 / 308

FUEL TANK, SEAT, TRIM

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.

- Immediately consult a doctor if you swallow fuel.

- Do not inhale fuel vapors.

- In case of skin contact, rinse the affected area with plenty of water.

- Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

- Change your clothing in case of fuel spills on them.

- Keep fuels correctly in a suitable canister, and out of the reach of children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

- Do not allow fuel to enter the groundwater, the soil, or the sewage system.

305313-10

305314-10

Preparatory work

- Drain the fuel from the fuel tank into a suitable container.

- Remove the seat. (

p. 77)

- Remove the fuel tank. (

p. 77)

Main work

- Remove nut

with the gasket.

- Remove fuel connection

with the gasket.

- Remove screws

- Pull out the fuel pump.

- Position the fuel pump.

- Mount fuel connection

with the gasket but do not tighten yet.

Guideline

Fuel connection on fuel pump

- Mount and tighten nut

with the gasket.

Guideline

10 Nm (7.4 lbf ft)

Nut, fuel pump fixation

15 Nm (11.1 lbf ft)

305313-10

305314-10

- Tighten fuel connection

Guideline

Fuel connection on fuel pump

- Mount and tighten screws

@).

Guideline

Screw, fuel pump

EJOT PT

110 Nm (7.4 lbf ft)

I 3 Nm (2.2 lbf ft)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands