Husqvarna FE 350 2015 Repair Manual Download Page 184

Page: 184 / 308

18 ENGINE

18.5.12 Installing the locking lever

Mount locking lever

with the washer, sleeve and spring.

Mount and tighten screw

Guideline

Screw, locking lever

6Nm

(4.4 lbf ft)

182

Loctite

243

™

18.5.13 Installing the shift drum locating unit

18.5.14 Installing the shift shaft

18.5.15 Installing the clutch basket

Push away locking lever

from the shift drum locating unit and position the

shift drum locating unit

•

Info

The flat areas of the shift drum locating unit are not symmetric.

Relieve tension from the locking lever.

Mount and tighten screw

CD.

Guideline

Screw, shift drum locating M6

10 Nm

(7.4 lbf ft)

Slide shift shaft

with the washer into the bearing seat.

Loctite

243

™

Push sliding plate

away from the shift drum locating unit

CD.

Insert the shift

shaft all the way.

Let the sliding plate engage in the shift drum locating unit.

Shift through the transmission.

Mount collar sleeve

and both needle bearings

Slide the clutch basket onto the gearbox main shaft. Turn the oil pump gear

until the gear teeth of the clutch basket mesh.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands