Husqvarna FE 350 2015 Repair Manual Download Page 213

Page: 213 / 308

24.2

THROTTLE VALVE BODY

Ad"ustin the idle s eed

Warning

Danger of accidents

The engine may go out spontaneously if the idle speed is set too low.

Set the idle speed to the specified value.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and death.
- Always make sure there is sufficient ventilation when running the

engine.

211

Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

Run the engine warm and push idle speed adjusting screw

all the way in.

Set the idle speed by turning the idle speed adjusting screw.
Guideline

Executing the initialization run

Idle speed

•

Info

2,050 ... 2,150 rpm

Turn counterclockwise to increase the idle speed.

Turn clockwise to decrease the idle speed.

Condition

The diagnostics tool is connected and running.

Execute

"Engine electronics"> "Functions"> "Delete adaptation values".

✓ The adaptation values are deleted.

Select

"Engine electronics" > "Measured values" > "Coolant temperature

sensor (TW1)".

✓ The coolant temperature is displayed during the initialization run.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and death.

- Always make sure there is sufficient ventilation when running the

engine.

Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

Start the engine without operating the throttle grip.

Guideline

Coolant temperature

< 25 °C (< 77 °F)

Let the engine idle until it reaches the specified temperature.
Guideline

Coolant temperature

•

Info

80 ... 90 °C (176 ... 194 °F)

Do not operate the throttle grip during the initialization process.

As soon as the specified temperature is reached, switch off the ignition.

•

Info

If the initialization is not completed or the initialization process is inter

rupted, the entire process must be restarted.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands