Husqvarna FE 350 2015 Repair Manual Download Page 163

Page: 163 / 308

18 ENGINE

Guideline

Piston/cylinder - mounting clearance

Size I

0.025 ... 0.047 mm (0.00098 ...

0.00185 in)

Size II

0.027 ... 0.049 mm (0.00106 ...

0.00193 in)

Wear limit

0.070 mm (0.00276 in)

18.4.17 Checking the piston ring end gap

302704-10

Remove the piston ring from the piston.

Place the piston ring in the cylinder and align with the piston.

Guideline

Below the upper edge of the cylinder

20 mm (0.79 in)

Measure the end gap with feeler gauge f).

Guideline

Piston ring - end gap

Compression ring

$ 0.40 mm ($ 0.0157 in)

Oil scraper ring

$ 0.80 mm ($ 0.0315 in)

If the end gap is greater than the specified measurement:

Check/measure the cylinder. (

p. 159)

If cylinder wear lies within the specified tolerance:

Change the piston ring.

Mount the piston ring with the marking facing toward the piston head.

18.4.18 Changing the camshaft bearing

308666-10

302767-10

Clamp special tool

into a vise.

Adjustment bush bridge (77229050044) (

p. 295)

Mount the camshaft on the special tool.

Remove screw

Pull camshaft gear (D off of the camshaft.

Extractor, camshaft gear (77229001044) (

p. 293)

Remove bearing

C,.

Oil the new bearing

and push it onto the camshaft.

Lubricated with engine oil

Degrease the cone of the camshaft and camshaft gear.

Mount camshaft gear (D.

Mount screw

but do not tighten yet.

Guideline

Screw, camshaft drive

M12x1

70 Nm

Loe-

161

sprocket

(51.6 lbf ft)

tite

243

™

/cone

308666-11

Repeat these steps for the second camshaft.

degreased

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands