Husqvarna FE 350 2015 Repair Manual Download Page 122

Page: 122 / 308

BRAKE SYSTEM

120

Press the brake caliper onto the brake disc by hand in order to push back the

brake piston and ensure that brake fluid does not flow out of the brake fluid reser

voir, extracting it by suction if it does.

•

Info

Make sure when pushing back the brake piston that you do not press the

brake caliper against the spokes.

Remove cotter pins (s), pull out pin

C,,

and remove the brake linings.

Clean the brake caliper and brake caliper support.

Check that leaf spring

in the brake caliper and sliding plate

in the brake

caliper support are seated correctly.

✓ The arrow on the leaf spring points in the rotation direction of the brake disc.

Insert the new brake linings, insert pin

C,,

and mount cotter pins (s).

•

Info

Always change the brake linings in pairs.

Make sure that decoupling plate @ is mounted on the piston side brake

lining.

Operate the foot brake lever repeatedly until the brake linings are in contact with

the brake disc and there is a pressure point.

- Add brake fluid to level 6).

Brake fluid DOT 4 (

p. 284)

Mount screw cap

with membrane

and O-ring.

Info

Clean up overflowed or spilled brake fluid immediately with water.

Checking the free travel of foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

Set the free travel on the foot brake lever in accordance with the specification.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands