Husqvarna FE 350 2015 Repair Manual Download Page 105

Page: 105 / 308

WHEELS

- Remove fittings (D. Take off the rear sprocket.

103

- Position the new rear sprocket. Mount and tighten the fittings.

Guideline

Nut, rear sprocket screw

35 Nm

(25.8 lbf ft)

- Slide new engine sprocket

onto the countershaft.

- Mount the new chain.

- Connect the chain with connecting link

C,.

Guideline

Loctite

2701

The closed side of the chain joint lock must face in the direction of travel.

- Install the rear wheel. (

!1ll

p. 97)

- Have an assistant operate the rear brake.

- Mount and tighten screw

with washer.

Guideline

Screw, engine sprocket

M10

- Position the engine sprocket cover.

- Mount and tighten screw

Guideline

Screw, clutch slave cylinder

- Mount and tighten screw (!}.

Guideline

Remaining screws, chassis

Finishing work

60 Nm

(44.3 lbf ft)

- Remove the motorcycle from the lift stand. (

p. 11)

Loctite

2701

110 Nm (7.4 lbf ft)

25 Nm (18.4 lbf ft)

14.7.11 Changing the rear wheel bearing

Preparatory work

- Raise the motorcycle with a lift stand.(� p. 11)

- Remove the rear wheel. (

�

p. 96)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands