Husqvarna FE 350 2015 Repair Manual Download Page 126

Page: 126 / 308

BRAKE SYSTEM

Mount bleeder cover

Bleeder cover (00029013006) (

p. 288)

Connect the bleeding device.

Bleeding device (00029013100) (

p. 288)

Open shut-off valve (D.

•

Info

Follow the operating instructions of the bleeding device.

Ensure that the filling pressure is correctly set at pressure gauge 6). If neces

sary, adjust the filling pressure at pressure regulator

G,.

Guideline

Filling pressure

2 ... 2.5 bar (29 ... 36 psi)

124

Pull off protection cap

of the bleeder screw. Connect the hose of the bleeder

bottle.

Bleeding device (00029013100) (

p. 288)

Open bleeder screw

by approx. one-half turn.

•

Info

Bleed until new brake fluid emerges from the bleeder bottle hose without

bubbles.

Tighten the bleeder screw.

Close shut-off valve (D.

Open the bleeder screw again until no more brake fluid emerges.

•

Info

This prevents overfilling of the brake fluid reservoir.

Tighten the bleeder screw. Remove the hose of the bleeder bottle. Mount the pro-

tection cap.

Disconnect the bleeding device. Remove the bleeder cover.

Stand the vehicle upright.

Correct the brake fluid up to marking (9.

Brake fluid DOT 4 (

p. 284)

Fit and tighten plug with oil screen and O-ring.

•

Info

Clean up overflowed or spilt brake fluid immediately with water.

Check the foot brake lever for a firm pressure point.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands