Husqvarna FE 350 2015 Repair Manual Download Page 75

Page: 75 / 308

10 EXHAUST

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

- Allow the exhaust system to cool down before performing any work on the vehicle.

Info

Soot particles accumulate on the screen of the spark arrestor over time.

This changes the performance characteristics.

Preparatory work

Remove the right side cover. (

�

p. 76)

Remove the main silencer. (

l!,JI

p. 71)

Main work

•--�

CG--•

�--•

Remove screws

and take off silencer cap @} with O-ring @).

Warning

Danger to health

Soot particles irritate the eyes and mucuous membranes.

Wear suitable breathing and eye protection when cleaning the main silencer and carbon screen.

Clean main silencer housing

and screen

of the spark arrestor with compressed air.

Mount a new 0-ring@) on silencer cap@}.

Position silencer cap@. Mount and tighten screws

Guideline

Screws on the main silencer

Finishing work

Install the main silencer. (

l!,JI

p. 71)

Install the right side cover. (

�

p. 77)

7 Nm (5.2 lbf ft)

402269-10

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands