Husqvarna FE 350 2015 Repair Manual Download Page 189

Page: 189 / 308

18 ENGINE

18.5.20 Installing the piston

302642-10

303078-10

Shift the joint of the piston rings by 120

Place the special tool on the oiled piston. Compress the piston rings using the

special tool.

Piston ring mounting tool (60029015000) (

E.,!1

p. 291)

✓ The piston rings are pushed together all the way.

Position the piston on the cylinder using the special tool.

Push the piston carefully into the cylinder from above.

Info

The piston rings should not catch or they will be damaged.

Ensure that piston mark

faces the exhaust side.

- Apply a thin layer of sealing compound in area G).

Loctite

591 O

Place the cylinder base gasket on.

Info

Ensure that the dowel pins are seated properly.

187

Cover the engine case opening with a cloth. Thread the timing chain through the

chain shaft. Mount the piston pin.

•

Info

In order to present them more clearly, the following steps are shown with a

removed piston.

Position the piston pin retainer.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands