Husqvarna FE 350 2015 Repair Manual Download Page 65

Page: 65 / 308

9.27

9.28

SHOCK ABSORBER, SWINGARM

201370-11

Checking the swingarm

Removing the swingarm

- Tighten screw

Guideline

Screw, shock absorber adjusting ring

- Check the swingarm for damage, cracking, and deformation.

I 5 Nm (3.7 lbf ft)

If the swingarm shows signs of damage, cracking, or deformation:

- Change the swingarm.

•

Info

Always change a damaged swingarm. Repair of the swingarm is

not authorized by Husqvarna Motorcycles.

Preparatory work

- Raise the motorcycle with a lift stand. (

p. 11)

- Remove the rear wheel. (

�

p. 96)

Main work

- Take the brake line out of the guide.

- Push the brake caliper forward, remove it, and hang it to the side.

Info

Cover the components to protect them against damage.

- Remove screws

and

- Remove the engine sprocket cover.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands