Husqvarna FE 350 2015 Repair Manual Download Page 168

Page: 168 / 308

18 ENGINE

308673-10

18.4.28 Checking the freewheel

302804-10

18.4.29 Removing the freewheel

Mount valve keys

CD.

•

Info

166

When mounting the valve keys, ensure that they are seated properly; it is

recommended to adhere the valve keys to the valves with a small amount

of grease.

Position cam levers

in the positions they had before they were removed.

Mount the cam lever shafts.

Remove screw

Mount and tighten screw plugs (D.

Guideline

Screw plug, cam lever axis

M 1 0x1

10 Nm (7.4 lbf ft)

Place shims into the valve spring retainers according to the installation position.

Insert freewheel gear

into the freewheel hub, turning the freewheel gear clock

wise; do not wedge.

Check the locking action of starter wheel

If the freewheel gear does not turn clockwise or if it does not lock counter

clockwise:

Change the free wheel.

Remove lock ring

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands