Husqvarna FE 350 2015 Repair Manual Download Page 86

Page: 86 / 308

FUEL TANK, SEAT, TRIM

12.12 Checkin

ressure

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

- Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

- Switch off the engine for refueling.

- Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

- If any fuel is spilled, wipe it off immediately.

- Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.

- Immediately consult a doctor if you swallow fuel.

- Do not inhale fuel vapors.

- In case of skin contact, rinse the affected area with plenty of water.

- Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

- Change your clothing in case of fuel spills on them.

- Keep fuels correctly in a suitable canister, and out of the reach of children.

Condition

The fuel tank is full.

Ensure that the battery voltage does not drop below 12.5 V.

The diagnostics tool is disconnected.

- Thoroughly clean the plug-in connection of the fuel line using compressed air.

•

Info

Under no circumstances should dirt enter into the fuel line. Dirt in the fuel

line clogs the injection valve.

- Press on the small metal plate and disconnect fuel hose connection

•

Info

Remaining fuel may flow out of the fuel hose.

- Mount special tool

Pressure tester (61029094000) (

�

p. 292)

- Mount special tool

with nozzle label 0,60.

Testing hose (61029093000) (

�

p. 291)

- Position the hose end in a fuel cannister.

Guideline

Minimum size of fuel cannister

110 I (2.6 US gal)

- Connect the diagnostics tool and start it.

- Select the

"Function test of fuel pump control"

actuator test.

Guideline

Maximum duration of the actuator test

3 min

- Check the fuel pressure with the filler cap closed.

Fuel pressure

When the fuel pump is active

If the specification is not reached:

- Open the filler cap. (

�

p. 76)

- Check the tank air vent system.

3.35 ... 3.65 bar (48.6 ... 52.9 psi)

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands