Husqvarna FE 350 2015 Repair Manual Download Page 28

Page: 28 / 308

FORK, TRIPLE CLAMP

201730-10

201732-11

-0-

- Mount spring

- Mount and tighten adapter

with spring

and washer.

Guideline

Adapter of piston rod

M6x0.5

- Position the spring.

12 Nm (8.9 lbf ft)

- Mount the compression shim stack

with the smaller washers facing down-

ward.

- Grind the piston on both sides on a surfacing plate using 1200 grit sandpaper.

- Clean the piston.

- Lubricate the piston ring.

Fork oil (SAE 4) (48601166S1) (

�

p. 284)

- Mount the piston with chamfer

facing down.

- Mount the rebound shim stack Ci) with the smaller washers facing upward.

- Press the piston downward against the spring.

✓ The piston should not squeeze the shims.

- Position valve @ in the hydrostop needle

fD.

Mount and tighten the hydrostop

needle.
Guideline

Hydrostop needle on piston rod

•

Info

M6x0.5

I 7 Nm (5.2 lbf ft)

silver hydrostop needle on compression damping side.

@) -

red hydrostop needle on rebound damping side.

- Unclamp the piston rod.

Summary of Contents for FE 350 2015





















































































































































































































































































































Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands

Husqvarna FE 350 2015, Repair Manual

Search results

Summary of Contents for FE 350 2015

Reviews:

Related manuals for FE 350 2015

Brands by name

Popular brands