manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

v

Contents 

5.4.2 Cleaning the Computer Case  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–6
5.4.3 Cleaning the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–6
5.4.4 Cleaning the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–7
5.4.5 Cleaning the Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–7

5.5 Service Considerations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–7

5.5.1 Power Supply Fan  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–7
5.5.2 Tools and Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–7
5.5.3 Screws  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–8
5.5.4 Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–8
5.5.5 Hard Drives  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–8
5.5.6 Lithium Coin Cell Battery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–9

6 Removal and Replacement Procedures— Microtower (MT) Chassis

6.1 Preparation for Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–1
6.2 External Security Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–2

6.2.1 Installing a Cable Lock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–2
6.2.2 Installing a Padlock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–2

6.3 Access Panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–3
6.4 Front Bezel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–4
6.5 Front Drive Bezels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–6

6.5.1 5.25" Drive Bezel Blank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–6
6.5.2 Diskette Drive Bezel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–7
6.5.3 3.5" Drive Bezel Blank  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–7

6.6 Memory Modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–8
6.7 Expansion Cards  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–9

6.7.1 Expansion Slot Cover   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–9
6.7.2 PCI Expansion Card   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–10

6.8 Cable Management  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–12

6.8.1 Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–13

6.9 Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–14

6.9.1 Drive Positions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–14
6.9.2 Removing a Drive  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–15
6.9.3 Installing a Drive  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–17

6.10Chassis Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–20
6.11Front I/O Panel Housing Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–21
6.12Front I/O Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–22
6.13Power Switch Assembly   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–23
6.14Heatsink  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–24
6.15Processor   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–25
6.16System Board  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–27
6.17Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–28

6.17.1Type 1 Battery Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–29
6.17.2Type 2 Battery Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–30
6.17.3Type 3 Battery Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–31

6.18Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–32
6.19Power Supply  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6–33

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM NetVista Quick Reference Manual preview
NetVista
Brand: IBM Pages: 68
IBM NetVista A30 Handboek Voor De Gebruiker preview
NetVista A30
Brand: IBM Pages: 54
Knoll Pixel Y-Leg Installation Instructions preview
Pixel Y-Leg
Brand: Knoll Pages: 2
IBM 6275 - PC 300 GL Technical Information Manual preview
6275 - PC 300 GL
Brand: IBM Pages: 88
BELINEA o.max Series User Manual preview
o.max Series
Brand: BELINEA Pages: 42
IBM IntelliStation POWER 9114 Model 275 Manual To The Installation preview
IntelliStation POWER 9114 Model 275
Brand: IBM Pages: 92
Roland DV-7DL G Owner'S Manual preview
DV-7DL G
Brand: Roland Pages: 1
EUROCOM LP295UB User Manual preview
LP295UB
Brand: EUROCOM Pages: 176
Compaq Presario 7360 Maintenance And Service Manual preview
Presario 7360
Brand: Compaq Pages: 69
Prentke Romich Company Accent 700 Hardware Manual preview
Accent 700
Brand: Prentke Romich Company Pages: 36
Vecow RCX-1000 User Manual preview
RCX-1000
Brand: Vecow Pages: 160
Compaq 6005 - Pro Microtower PC Illustrated Parts & Service Map preview
6005 - Pro Microtower PC
Brand: Compaq Pages: 4
Vivo CART-V06A Instruction Manual preview
CART-V06A
Brand: Vivo Pages: 12
Dell EMS01 Getting Started Manual preview
EMS01
Brand: Dell Pages: 72
Dell Precision 3430 Setup And Specifications preview
Precision 3430
Brand: Dell Pages: 36
Gateway 300X User Manual preview
300X
Brand: Gateway Pages: 118
Wincor Nixdorf P4-EPC/B-E1 Operating Manual preview
P4-EPC/B-E1
Brand: Wincor Nixdorf Pages: 32
Franklin Computer PC 8000 User'S Reference Manual preview
PC 8000
Brand: Franklin Computer Pages: 108

Brands by name

Popular brands

Load more brands