manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

3–7

Desktop Management

6. Select 

File

 

> Replicated Setup 

> 

Save to Removable Media

. Follow the instructions on the 

screen to create the configuration diskette or USB flash media device.

7. Turn off the computer to be configured and insert the configuration diskette or USB flash 

media device.

8. Turn on the computer to be configured.

9. As soon as the computer is turned on, press and hold the 

F10

 key until you enter Computer 

Setup. Press 

Enter

 to bypass the title screen, if necessary.

10. Select 

File

 

> Replicated Setup 

> 

Restore from Removable Media

, and follow the 

instructions on the screen.

11. Restart the computer when the configuration is complete.

Copying to Multiple Computers

Ä

CAUTION: 

A setup configuration is model-specific. File system corruption may result if source and target 

computers are not the same model. For example, do not copy the setup configuration from a dc7100 
Ultra-Slim Desktop to a dx6100 Slim Tower.

This method takes a little longer to prepare the configuration diskette or USB flash media device, 
but copying the configuration to target computers is significantly faster.

✎

A bootable diskette is required for this procedure or to create a bootable USB flash media device. 
If Windows XP is not available to use to create a bootable diskette, use the method for copying to 
a single computer instead (see 

“Copying to Single Computer” on page 6

).

1. Create a bootable diskette or USB flash media device. See 

“Supported USB Flash Media 

Device” on page 8

 or 

“Unsupported USB Flash Media Device” on page 10.

Ä

CAUTION: 

Not all computers can be booted from a USB flash media device. If the default boot order in 

the Computer Setup (F10) Utility lists the USB device before the hard drive, the computer can be booted 
from a USB flash media device. Otherwise, a bootable diskette must be used.

2. Select a setup configuration to copy. Turn off the computer. If you are in Windows, click 

Start > Shut Down > Shut Down.

3. If you are using a USB flash media device, insert it now.

4. Turn on the computer.

5. As soon as the computer is turned on, press and hold the 

F10

 key until you enter Computer 

Setup. Press 

Enter

 to bypass the title screen, if necessary.

✎

If you do not press the 

F10

 key at the appropriate time, you must restart the computer and press 

and hold the 

F10

 key again to access the utility.

 

 

If you are using a PS/2 keyboard, you may see a Keyboard Error message—disregard it.

6. If you are using a a diskette, insert it now.

7. Select 

File > Replicated Setup > Save to Removable Media.

 Follow the instructions on the 

screen to create the configuration diskette or USB flash media device.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

AOpen DE6140 Series User Manual preview
DE6140 Series
Brand: AOpen Pages: 20
UUGear Witty Pi User Manual preview
Witty Pi
Brand: UUGear Pages: 25
GARANT eLevel User Manual preview
eLevel
Brand: GARANT Pages: 60
Vivo DESK-V000W Instruction Manual preview
DESK-V000W
Brand: Vivo Pages: 3
Dell Alienware Area-51m R2 Setup And Specifications preview
Alienware Area-51m R2
Brand: Dell Pages: 21
Dell Alienware Aurora R13 Setup And Specifications preview
Alienware Aurora R13
Brand: Dell Pages: 20
Dell Alienware Aurora R11 Setup And Specifications preview
Alienware Aurora R11
Brand: Dell Pages: 20
Dell Alienware Aurora R3 Manual preview
Alienware Aurora R3
Brand: Dell Pages: 70
Dell Alienware Area-51 ALX Specifications preview
Alienware Area-51 ALX
Brand: Dell Pages: 7
Dell Alienware Aurora - R2 Setup And Specifications preview
Alienware Aurora - R2
Brand: Dell Pages: 17
Dell 3250 Product Manual preview
3250
Brand: Dell Pages: 240
Dell Alienware Area-51m R2 Service Manual preview
Alienware Area-51m R2
Brand: Dell Pages: 94
Dell Alienware 0JYTRGA00 Owner'S Manual preview
Alienware 0JYTRGA00
Brand: Dell Pages: 68
Dell ALIENWARE AURORA Service Manual preview
ALIENWARE AURORA
Brand: Dell Pages: 117
Dell Alienware Aurora R11 Service Manual preview
Alienware Aurora R11
Brand: Dell Pages: 109
Dell Alienware Area-51 ALX Service Manual preview
Alienware Area-51 ALX
Brand: Dell Pages: 103
Dell Alienware Area-51 R5 Service Manual preview
Alienware Area-51 R5
Brand: Dell Pages: 121
Dell Alienware Area-51 R4 Service Manual preview
Alienware Area-51 R4
Brand: Dell Pages: 128

Brands by name

Popular brands

Load more brands