HP Compaq dc5100 Series Service & Reference Manual Download Page 77 | Manualshive

Page: 77 / 230

background image

Service Reference Guide, dc5100

376220-001

5–9

Identifying the Chassis, Routine Care, and Disassembly Preparation

5.5.6 Lithium Coin Cell Battery

The battery that comes with the computer provides power to the real-time clock and has a
lifetime of about three years.

See the appropriate removal and replacement chapter for the chassis you are working on in this
guide for instructions on the replacement procedures.

Å

WARNING:

This computer contains a lithium battery. There is a risk of fire and chemical burn if the

battery is handled improperly. Do not disassemble, crush, puncture, short external contacts, dispose in
water or fire, or expose it to temperatures higher than 140ºF (60ºC).

Ä

CAUTION:

Batteries, battery packs, and accumulators should not be disposed of together with the

general household waste.

«
...
75
76
77
78
79
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Brand: IBM Pages: 40

Brand: IBM Pages: 52

Brand: Portwell Pages: 50

Brand: Lenovo Pages: 10

Brand: Lenovo Pages: 54

Brand: Lenovo Pages: 56

Brand: Lenovo Pages: 62

Brand: Lenovo Pages: 66

Brand: Lenovo Pages: 70

Brand: Lenovo Pages: 70

ThinkCentre M93/p

Brand: Lenovo Pages: 2

Brand: Lenovo Pages: 85

Brand: Lenovo Pages: 90

Brand: Lenovo Pages: 98

ThinkCentre Types 8288

Brand: Lenovo Pages: 44

ThinkCentre Tiny-in-One 23

Brand: Lenovo Pages: 45

ThinkCentre 3512

Brand: Lenovo Pages: 128

ThinkCentre neo 50s Gen 3

Brand: Lenovo Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands