manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

7–18

376220-001

Service Reference Guide, dc5100

Removal and Replacement Procedures— Small Form Factor (SFF) Chassis

7.8 Expansion 

Card 

7.8.1  Expansion Card Retainer 

1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to 

unlock the lock.

2. Turn off the computer properly through the operating system, then turn off any external 

devices.

3. Disconnect the power cord from the power outlet and disconnect any external devices.

4. Remove the computer from the stand and lay the computer on its side.

5. Remove the computer cover. Refer to 

Section 7.4, “Computer Cover”

6. Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab 

on the latch and rotating the latch to the full open position 

1

.

7. Remove the single screw that keeps the card retainer in place 

2

 and slide the retainer to the 

left to remove it from the chassis 

3

.

To install the card retainer, reverse the removal procedure.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Panasonic CF-30 Series Operating Instruction preview
CF-30 Series
Brand: Panasonic Pages: 15
GABOR DMSS-502 User Manual preview
DMSS-502
Brand: GABOR Pages: 24
Dell EC280 Owner'S Manual preview
EC280
Brand: Dell Pages: 77
Samsung NX-N2-T Brochure & Specs preview
NX-N2-T
Brand: Samsung Pages: 2
Samsung DP700A3D-A01US Specifications preview
DP700A3D-A01US
Brand: Samsung Pages: 2
Samsung eGO-note User Manual preview
eGO-note
Brand: Samsung Pages: 39
Samsung SUR40 User Manual preview
SUR40
Brand: Samsung Pages: 48
Samsung 350V4X User Manual preview
350V4X
Brand: Samsung Pages: 21
Samsung 450R4V User Manual preview
450R4V
Brand: Samsung Pages: 27
Samsung 350E4X User Manual preview
350E4X
Brand: Samsung Pages: 31
Samsung NX-N2 User Manual preview
NX-N2
Brand: Samsung Pages: 78
Samsung TC222W User Manual preview
TC222W
Brand: Samsung Pages: 96
Samsung DP700C6A-X01US User Manual preview
DP700C6A-X01US
Brand: Samsung Pages: 106
Samsung DP700AK-K02US User Manual preview
DP700AK-K02US
Brand: Samsung Pages: 116
Samsung DP700A7D-A03US User Manual preview
DP700A7D-A03US
Brand: Samsung Pages: 134
Samsung Personal Computer User Manual preview
Personal Computer
Brand: Samsung Pages: 143
Samsung DP700A3D User Manual preview
DP700A3D
Brand: Samsung Pages: 145
Samsung 400S8A User Manual preview
400S8A
Brand: Samsung Pages: 118

Brands by name

Popular brands

Load more brands