manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

D–6

376220-001

Service Reference Guide, dc5100

Solving Diskette Problems

Solving Diskette Problems 

Problem

Cause

Solution

Diskette drive light stays on.

Diskette is damaged.

In Microsoft Windows XP, right-click 

Start

, click 

Explore

, and select a 

drive. Select 

File > Properties > 

Tools

. Under 

Error-checking

, 

click 

Check Now

.

Diskette is incorrectly 
inserted.

Remove diskette and reinsert.

Drive button is not 
pushed in.

Push in drive button.

Files on diskette are 
damaged.

Check the program diskettes.

Drive cable is not 
properly connected.

Reconnect power cable. Ensure that 
all four pins are connected.

Drive not found.

Cable is loose.

Reseat diskette drive data and 
power cables.

Removable drive is not 
seated properly.

Reseat the drive.

You attempted to hot 
plug a removable 
hard drive that has 
DriveLock security 
enabled. (This feature 
supported on select 
models only.)

Shut down the computer. Insert the 
drive into the MultiBay, if it is not 
already inserted. Turn on the 
computer.

Diskette drive cannot write 
to a diskette.

Diskette is not 
formatted.

Format the diskette.

Diskette is 
write-protected.

Use another diskette or remove the 
write protection.

Writing to the wrong 
drive.

Check the drive letter in the path 
statement.

Not enough space is 
left on the diskette.

Use another diskette.

Diskette write control is 
enabled.

Use Computer Setup to check the 
storage security feature disabled 
settings.

Diskette is damaged.

Replace the damaged disk.

Cannot format diskette.

Invalid media reported.

When formatting a disk in MS-DOS, 
you may need to specify diskette 
capacity. For example, to format a 
1.44-MB diskette, type the following 
command at the MS-DOS prompt:

FORMAT A: /F:1440

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM 5110 Basic Introduction preview
5110
Brand: IBM Pages: 170
IBM 5110 Maintenance Analysis Procedures preview
5110
Brand: IBM Pages: 257
IBM 5110 General Information And Physical Planning Manual preview
5110
Brand: IBM Pages: 63
Xerox 8010 Hardware Reference Manual preview
8010
Brand: Xerox Pages: 20
VALKPC VF-1 User Manual preview
VF-1
Brand: VALKPC Pages: 20
CyberResearch CYRAQ PPC Series User Manual preview
CYRAQ PPC Series
Brand: CyberResearch Pages: 103
Life Fitness 320-00-00010-01 Owner'S Manual preview
320-00-00010-01
Brand: Life Fitness Pages: 36
Neousys Technology Nuvo-6000 Series User Manual preview
Nuvo-6000 Series
Brand: Neousys Technology Pages: 100
Asus ProArt PA Series User Manual preview
ProArt PA Series
Brand: Asus Pages: 40
Asus PB50 BR072MD User Manual preview
PB50 BR072MD
Brand: Asus Pages: 46
Asus Pundit P1-AH1 Quick Installation Manual preview
Pundit P1-AH1
Brand: Asus Pages: 80
Asus Pundit P2-PE2 Manual preview
Pundit P2-PE2
Brand: Asus Pages: 76
Asus P6-P8H61E User Manual preview
P6-P8H61E
Brand: Asus Pages: 75
Asus PB40 User Manual preview
PB40
Brand: Asus Pages: 44
Asus PUNDIT P2-AE2 User Manual preview
PUNDIT P2-AE2
Brand: Asus Pages: 90
Asus Prodigy P4S Quick Installation preview
Prodigy P4S
Brand: Asus Pages: 56
Asus P5G43 V4-Series User Manual preview
P5G43 V4-Series
Brand: Asus Pages: 110
Asus PN62S User Manual preview
PN62S
Brand: Asus Pages: 44

Brands by name

Popular brands

Load more brands