manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

D–21

Power LED flashes Red five 
times, once every second, 
followed by a two second 
pause, and the computer 
beeps five times. Beeps 
continue for five iterations 
after which the LED flashes 
will continue until the 
problem is resolved.

Memory is installed 
incorrectly or is bad.

1. Reseat DIMMs. 

2. Replace DIMMs one at a time to 

isolate the faulty module.

3. Replace third-party memory 

with HP memory.

4. Replace the system board.

Power LED flashes Red six 
times, once every second, 
followed by a two second 
pause, and the computer 
beeps six times. Beeps 
continue for five iterations 
after which the LED flashes 
will continue until the 
problem is resolved.

Video card is not seated 
properly or is bad, or 
system board is bad.

For systems with a graphics card:

1. Reseat the graphics card. Power 

on the system.

2. Replace the graphics card.
3. Replace the system board.

For systems with integrated 
graphics, replace the system board.

Power LED flashes Red ten 
times, once every second, 
followed by a two second 
pause, and the computer 
beeps ten times. Beeps 
continue for five iterations 
after which the LED flashes 
will continue until the 
problem is resolved

Bad option card.

1. Check each option card by 

removing the cards one at time 
(if multiple cards), then power 
on the system to see if fault goes 
away.

2. Once bad card is identified, 

remove and replace bad option 
card.

3. Replace the system board.

Solving Hardware Installation Problems 

(Continued)

Problem

Cause

Solution

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

National Instruments 500 Series Getting Started preview
500 Series
Brand: National Instruments Pages: 93
7starlake ROC254A User Manual preview
ROC254A
Brand: 7starlake Pages: 8
Simrad MARINE COMPUTER - INSTALLATION REV A Installation Manual preview
MARINE COMPUTER - INSTALLATION REV A
Brand: Simrad Pages: 40
Ruijie Networks Rain400 Series Manual preview
Rain400 Series
Brand: Ruijie Networks Pages: 30
Vivo DESK-V000Q Instruction Manual preview
DESK-V000Q
Brand: Vivo Pages: 3
Siemens SIMATIC VPU200-3104 Hardware Manual preview
SIMATIC VPU200-3104
Brand: Siemens Pages: 28
Siemens SIMATIC Rack PC IL 40 Getting Started preview
SIMATIC Rack PC IL 40
Brand: Siemens Pages: 40
Siemens SIMATIC PC BI10 Technical Description preview
SIMATIC PC BI10
Brand: Siemens Pages: 45
Siemens SIMATIC RI 45 PIII Series Manual preview
SIMATIC RI 45 PIII Series
Brand: Siemens Pages: 132
Siemens Simatic series Operating Instructions Manual preview
Simatic series
Brand: Siemens Pages: 194
Siemens SIMATIC IPC627D Operating Instructions Manual preview
SIMATIC IPC627D
Brand: Siemens Pages: 186
Larson Electronics SPG-4G-18-8-FM Instruction Manual preview
SPG-4G-18-8-FM
Brand: Larson Electronics Pages: 2
Sony VAIO VPCCW Series Quick Start Manual preview
VAIO VPCCW Series
Brand: Sony Pages: 2
Sony VAIO VGX-XL1A Release Note preview
VAIO VGX-XL1A
Brand: Sony Pages: 1
Sony VAIO VGX-XL3 Specifications preview
VAIO VGX-XL3
Brand: Sony Pages: 2
Sony VAIO VGN-Z820G Specifications preview
VAIO VGN-Z820G
Brand: Sony Pages: 2
Sony VAIO VPCCW Series Service Manual preview
VAIO VPCCW Series
Brand: Sony Pages: 24
Sony VAIO VGNUX27GN Brochure & Specs preview
VAIO VGNUX27GN
Brand: Sony Pages: 21

Brands by name

Popular brands

Load more brands