HP Compaq dc5100 Series Service & Reference Manual Download Page 16 | Manualshive

Page: 16 / 230

background image

2–6

376220-001

Service Reference Guide, dc5100

Setup Utilities and Diagnostics Features

Storage

(continued)

Device
Configuration

(continued)

Translation Parameters

(ATA disks only)

✎

This feature appears only when User translation mode is selected.

Allows you to specify the parameters (logical cylinders, heads, and
sectors per track) used by the BIOS to translate disk I/O requests
(from the operating system or an application) into terms the hard
drive can accept. Logical cylinders may not exceed 1024. The
number of heads may not exceed 256. The number of sectors per
track may not exceed 63. These fields are only visible and
changeable when the drive translation mode is set to User.

Storage Options

Removable Media Boot

Enables/disables ability to boot the system from removable media.

Legacy Diskette Write

Enables/disables ability to write data to legacy diskettes.

✎

After saving changes to Removable Media Write, the computer
will restart. Turn the computer off, then on, manually.

BIOS DMA Data Transfers

Allows you to control how BIOS device I/O requests are serviced.
When “Enable” is selected, the BIOS will service ATA device read
and write requests with DMA data transfers. When “Disable” is
selected, the BIOS will service ATA device read and write requests
with PIO data transfers.

SATA Emulation

Allows you to choose how the SATA controller and devices are
accessed by the operating system.
“Separate IDE Controller” is the default option. Up to 4 SATA and 2
PATA devices may be accessed in this mode. The SATA and PATA
controllers appear as two separate IDE controllers. Use this option
with Microsoft Windows 2000 and Windows XP.

• SATA 0 is seen as SATA Primary Device 0
• SATA 1 (if present) is seen as SATA Secondary Device 0

“Combined IDE Controller” is the other option. Up to 2 PATA and 2
SATA devices may be accessed in this mode. The SATA and PATA
controllers appear as one combined IDE controller. Use this option
with Microsoft Windows 98 and earlier operating systems.

• PATA Primary Device 0 replaces SATA 1
• PATA Primary Device 1 replaces SATA 3

IDE Controller

Allows you to enable or disable the primary IDE controller. This
feature is supported on some models.

Primary SATA Controller

Allows you to enable or disable the Primary SATA controller.

Heading

Option

Description

✎

Support for specific Computer Setup options may vary depending on the hardware configuration.

«
...
14
15
16
17
18
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Brand: IBM Pages: 136

Brand: IBM Pages: 202

ThinkPad G40 Series

Brand: IBM Pages: 160

Brand: Gateway Pages: 34

Brand: Gateway Pages: 142

Brand: Gateway Pages: 288

Brand: Gateway Pages: 2

Brand: Gateway Pages: 24

Brand: Gateway Pages: 52

Brand: DFI Pages: 69

Brand: Vecow Pages: 65

Brand: Clarke Pages: 8

Alienware Area-51m R2

Brand: Dell Pages: 21

Alienware Aurora R13

Brand: Dell Pages: 20

Alienware Aurora R11

Brand: Dell Pages: 20

Alienware Aurora R3

Brand: Dell Pages: 70

Alienware Area-51 ALX

Brand: Dell Pages: 7

Alienware Aurora - R2

Brand: Dell Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands