HP Compaq dc5100 Series Service & Reference Manual Download Page 8

Page: 8 / 230

1–2

376220-001

Service Reference Guide, dc5100

Installing the Operating System

1.2 Transferring Files and Settings

Use the Microsoft Windows XP Files and Settings Transfer Wizard to move files and settings
from an old computer to a new one. Click

Start > All Programs > Accessories > System Tools

> Files and Settings Transfer Wizard

1.3 Backing Up and Restoring Files

1.3.1 Creating a Backup File—Windows XP Professional

1. Click

Start > All Programs > Accessories > System Tools > Backup

2. Use the Backup or Restore Wizard to create a backup file or tape.

✎

A backup file can be saved to a hard disk, a floppy disk, CD, USB flash media device, tape drive,
or to any other removable or nonremovable media.

1.3.2 Restoring from the Backup File—Windows XP Professional

1. Click

Start > All Programs > Accessories > System Tools > Backup

2. Use the Backup or Restore Wizard to restore files from a backup file.

✎

A backup file can be on a hard disk, a floppy disk, CD, USB flash media device, tape drive, or
any other removable or nonremovable media.

1.4 Converting to NTFS

Windows XP Professional

To convert a FAT or FAT32 volume to NTFS,

1. Click

Start > All Programs > Accessories > Command Prompt

2. Type

convert

drive_letter

: /fs:ntfs

(where

drive_letter

is the volume to be converted) and

press

Enter

1.5 HP

Software

The Microsoft Windows XP Professional operating system is preinstalled on the computer and
will be configured automatically the first time the computer is turned on. The following HP
software may also be installed at that time on selected models:

■

Computer Setup Utilities

■

HP Support Software including device drivers

■

Configuration Record

■

Online

Safety & Comfort Guide

■

Power Management with energy saver features

■

Security Management tools

Summary of Contents for Compaq dc5100 Series







































































































































































































































Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands

HP Compaq dc5100 Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands