HP Compaq dc5100 Series Service & Reference Manual Download Page 186

Page: 186 / 230

D–2

376220-001

Service Reference Guide, dc5100

Solving Minor Problems

Problem

Cause

Possible Solution

Computer appears
locked up and will not
turn off when the power
button is pressed.

Software control of the
power switch is not
functional.

1. Press and hold the power button

for at least four seconds until the
computer turns off.

2. Disconnect electrical plug from

outlet.

Computer will not
respond to USB
keyboard or mouse.

Computer is in

standby

mode.

Press the power button to resume from

standby

mode.

System has locked up.

Restart computer.

CAUTION:

When attempting to resume from

standby

mode, do not hold down the power

button for more than four seconds. Otherwise, the computer will shut down and you will lose

any unsaved data.

Computer date and
time display is incorrect.

RTC (real-time clock)
battery may need to be
replaced.

1. Reset the date and time under

Control Panel

2. Replace the RTC battery.

Computer appears to
pause periodically.

Network driver is loaded
and no network
connection is established.

Establish a network connection, or
use Computer Setup or Microsoft
Windows Device Manager to disable
the network controller.

Cursor will not move
using the arrow keys on
the keypad.

The

Num Lock

key

may be on.

Press the

Num Lock

key. The

Num

Lock

key can be disabled (or

enabled) in Computer Setup.

Cannot remove
computer cover or
access panel.

Smart Cover Lock,
featured on some
computers, is locked.

1. Unlock the Smart Cover Lock

using Computer Setup.

2. Use the Smart Cover FailSafe Key

in case of forgotten password,
power loss, or computer
malfunction.

Poor performance is
experienced.

Processor is hot.

1. Ensure airflow to the computer is

not blocked.

2. Ensure the fans are connected

and working properly (some fans
only operate when needed).

3. Ensure the processor heatsink is

installed properly.

Hard drive is full.

Transfer data from the hard drive to
create more space on the hard drive.

Low on memory.

Add more memory.

Hard drive fragmented.

Defragment hard drive.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands

HP Compaq dc5100 Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands