manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

iv

376220-001

Service Reference Guide, dc5100

Contents

3.4 Asset Tracking and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–13

3.4.1 Password Security  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–17
3.4.2 Establishing a Setup Password Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . .  3–17
3.4.3 Establishing a Power-On Password Using Computer Setup  . . . . . . . . . . . . . . . . . . . . . .  3–17
3.4.4 DriveLock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–20
3.4.5 Smart Cover Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–22
3.4.6 Master Boot Record Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–24
3.4.7 Before You Partition or Format the Current Bootable Disk  . . . . . . . . . . . . . . . . . . . . . .  3–25
3.4.8 Cable Lock Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–25
3.4.9 Fingerprint Identification Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–25

3.5 Fault Notification and Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–26

3.5.1 Drive Protection System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–26
3.5.2 Surge-Tolerant Power Supply  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–26
3.5.3 Thermal Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3–26

4 Serial and Parallel ATA Drive Guidelines and Features

4.1 SATA and PATA Device Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–1
4.2 ATA Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–2

4.2.1 SATA Data Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–2
4.2.2 SATA Power Cable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–2
4.2.3 PATA Data Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–3
4.2.4 PATA Power Cable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–3
4.2.5 PATA Cable Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–4

4.3 PATA Drive Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–5

4.3.1 PATA Device Classes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–5
4.3.2 PATA Attach Sequence Rules by Class Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–6
4.3.3 PATA Attach Sequence Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–7
4.3.4 PATA Additional Drive Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–9

4.4 ATA SMART Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–10
4.5 Drive Capacities  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–10
4.6 SATA BIOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–11

4.6.1 Legacy Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–11
4.6.2 Native Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–11

4.7 Mixed Devices Boot and Drive Letter Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4–12

5 Identifying the Chassis, Routine Care, and Disassembly Preparation

5.1 Chassis Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–1

5.1.1 Microtower (MT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–1
5.1.2 Small Form Factor (SFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–2

5.2 Electrostatic Discharge Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–3

5.2.1 Generating Static  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–3
5.2.2 Preventing Electrostatic Damage to Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–3
5.2.3 Personal Grounding Methods and Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–4
5.2.4 Grounding the Work Area  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–4
5.2.5 Recommended Materials and Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–4

5.3 Operating Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–5
5.4 Routine Care  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–5

5.4.1 General Cleaning Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5–5

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Baaske Medical Docpad 10c W User Manual preview
Docpad 10c W
Brand: Baaske Medical Pages: 40
IBM Power 775 Service Procedure preview
Power 775
Brand: IBM Pages: 27
Radio Shack TRS-80 Color Computer 2 User Manual preview
TRS-80 Color Computer 2
Brand: Radio Shack Pages: 44
FabiaTech FX5502 User Manual preview
FX5502
Brand: FabiaTech Pages: 62
Digital Equipment FR-856E*-WB Service Maintenance Manual preview
FR-856E*-WB
Brand: Digital Equipment Pages: 74
Sun Microsystems Ultra 25 Getting Started Manual preview
Ultra 25
Brand: Sun Microsystems Pages: 14
IBM Aptiva 2165 Hardware Maintenance Service preview
Aptiva 2165
Brand: IBM Pages: 167
Büttner Elektronik MT iQ Basic Instruction Manual preview
MT iQ Basic
Brand: Büttner Elektronik Pages: 36
Compaq 6005 - Pro Microtower PC Illustrated Parts & Service Map preview
6005 - Pro Microtower PC
Brand: Compaq Pages: 4
Intel NUC7CJYH Manual preview
NUC7CJYH
Brand: Intel Pages: 2
Arista AP-3500-E01 User Manual preview
AP-3500-E01
Brand: Arista Pages: 47
Acer Aspire Z800 User Manual preview
Aspire Z800
Brand: Acer Pages: 20
Acer AX3950-U2042 Buyer'S Manual preview
AX3950-U2042
Brand: Acer Pages: 3
Acer Aspire Z5610 Series Specifications preview
Aspire Z5610 Series
Brand: Acer Pages: 2
Acer AX3200-B3530A Buyer'S Manual preview
AX3200-B3530A
Brand: Acer Pages: 4
Acer Aspire ZC-602 User Manual preview
Aspire ZC-602
Brand: Acer Pages: 52
Acer Chromebase CA24I2 User Manual preview
Chromebase CA24I2
Brand: Acer Pages: 31
Acer Aspire Z1220 User Manual preview
Aspire Z1220
Brand: Acer Pages: 29

Brands by name

Popular brands

Load more brands