HP Compaq dc5100 Series Service & Reference Manual Download Page 61 | Manualshive

Page: 61 / 230

background image

Service Reference Guide, dc5100

376220-001

4–5

Serial and Parallel ATA Drive Guidelines and Features

4.3 PATA Drive Installation Guidelines

Most computer system boards have two or fewer Parallel ATA (PATA) channels with a dedicated
connector for each channel. When two channels are present, one is designated as the Primary and
the other as the Secondary Channel.

Each of the two channels can have up to two devices attached to it. All drives are connected to a
channel using an industry-standard 80-conductor cable.

✎

The industry standard 1.44 MB diskette drive has its own separate channel and is not included as
a part of the maximum four drives.

HP does not support the use of PATA (IDE) hard drives when SATA hard drives are installed on
the computer.

Each drive attached to a channel must have a drive designation. If a drive is attached to the
Device 0 cable position and its cable-select jumper is present, the drive is designated as Device 0.
Similarly, if a drive is attached to the Device 1 cable position and its cable-select jumper is
present, the drive is designated as Device 1.

For optimal performance of a computer system, all drives need to be attached to the PATA
channel(s) in a specified sequence. This sequence is determined by the device class of the drives
and by specific attach sequence rules.

4.3.1 PATA Device Classes

In order to determine the best drive attach sequence, ATA/ATAPI drives are segregated into four
different classes based upon the bandwidth demands they place on an ATA channel. The most
demanding devices are in Class 1 and the least demanding are in Class 4.

General Attach Guidelines

■

The lower the device class number, the faster the device and the more bandwidth required.

■

Drives installed in the Device 0 positions on both the primary and secondary channels
receive the greatest possible bandwidth.

■

The bootable ATA hard drive should always be installed on the primary channel in the
Device 0 position.

Class 1

Hard

Drives

Class 2

High Speed

Optical Drives

Class 3

Optical Storage

Drives

Class 4

Magnetic

Storage Drives

ATA-100

ATA-66

ATA-33

DVD

DVD-CD R/W

R/W CD-ROM

CD-ROM

LS-120

Tape

Zip

«
...
59
60
61
62
63
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Brand: Gateway Pages: 2

IntelliStation Z Pro Type 6866

Brand: IBM Pages: 194

Brand: GARANT Pages: 60

iDEQ-T1 IN294KT1

Brand: Biostar Pages: 53

Brand: AWOW Pages: 4

Brand: Advanced Micro Computers Pages: 77

Qosmio G50 Series

Brand: Toshiba Pages: 446

Brand: Fanvil Pages: 12

Brand: Fanvil Pages: 15

Brand: Fanvil Pages: 54

Brand: Fellowes Pages: 21

XPC slim XH510G2

Brand: Shuttle Pages: 3

Brand: Shuttle Pages: 27

Brand: Shuttle Pages: 25

Brand: Alpha Microsystems Pages: 23

Brand: AMSTRAD Pages: 45

Brand: AMSTRAD Pages: 520

Brand: Janz Tec Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands