HP Compaq dc5100 Series Service & Reference Manual Download Page 73 | Manualshive

Page: 73 / 230

background image

Service Reference Guide, dc5100

376220-001

5–5

Identifying the Chassis, Routine Care, and Disassembly Preparation

■

Static awareness labels

■

Wrist straps and footwear straps providing one-/- 10% resistance

■

Material handling packages

■

Conductive plastic bags

■

Conductive plastic tubes

■

Conductive tote boxes

■

Opaque shielding bags

■

Transparent metallized shielding bags

■

Transparent shielding tubes

5.3 Operating

Guidelines

To prevent overheating and to help prolong the life of the computer:

■

Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and
cold.

■

Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all
vented sides of the computer and above the monitor to permit the required airflow.

■

Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place
the keyboard, with the keyboard feet down, directly against the front of the desktop unit as
this also restricts airflow.

■

Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other
foreign matter can block the vents and limit the airflow.

■

Never operate the computer with the cover or side panel removed.

■

Do not stack computers on top of each other or place computers so near each other that they
are subject to each other’s re-circulated or preheated air.

■

If the computer is to be operated within a separate enclosure, intake and exhaust ventilation
must be provided on the enclosure, and the same operating guidelines listed above will still
apply.

■

The computer is designed to operate continuously (24x7), provided that the operating
guidelines listed above are met.

■

Install or enable power management functions of the operating system or other software,
including sleep states.

5.4 Routine

Care

5.4.1 General Cleaning Safety Precautions

1. Never use solvents or flammable solutions to clean the computer.

2. Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth

and then use the cloth on the component.

3. Always unplug the computer when cleaning with liquids or damp cloths.

4. Always unplug the computer before cleaning the keyboard, mouse, or air vents.

«
...
71
72
73
74
75
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IntelliStation E Pro 6836

Brand: IBM Pages: 156

BX-951-DC series

Brand: Contec Pages: 111

Brand: Gateway Pages: 2

Brand: Gateway Pages: 98

Brand: Gateway Pages: 190

Brand: Datatech Enterprises Pages: 130

Brand: Cincoze Pages: 183

Brand: Partner Pages: 52

Brand: Olympus Pages: 8

Brand: Janz Tec Pages: 27

Brand: EVOC Pages: 49

Brand: EVOC Pages: 51

Brand: EVOC Pages: 67

Brand: EVOC Pages: 123

Brand: Datavideo Pages: 13

Brand: Ronde & Schwarz Pages: 98

Brand: IBASE Technology Pages: 14

Brand: Lanner Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands