HP Compaq dc5100 Series Service & Reference Manual Download Page 185 | Manualshive

Page: 185 / 230

background image

Service Reference Guide, dc5100

376220-001

D–1

D

Troubleshooting Without Diagnostics

Preliminary Checklist

This section describes some simple, preliminary tests and guidelines for troubleshooting the
computer without using the diagnostics.

■

Are the computer and monitor connected to a working electrical outlet?

■

Is the voltage select switch is set to the appropriate voltage for your region (115V or 230V)?

■

Is the computer turned on?

■

Is the green power light illuminated?

■

Is the monitor turned on?

■

Is the green monitor light illuminated?

■

Turn up the monitor brightness and contrast controls if the monitor is dim.

■

If the system has multiple video sources (embedded or PCI adapters) installed (embedded
video on select models only) and a single monitor, the monitor must be plugged into the
monitor connector on the source selected as the primary VGA adapter. During boot, the other
monitor connectors are disabled and if the monitor is connected into these ports, the monitor
will not function. You can select which source will be the default VGA source in Computer
(F10) Setup.

■

Press and hold any key. If the system beeps, then the keyboard is operating correctly.

■

Check all cables for loose or incorrect connections.

■

Reconfigure the computer after installing a non–Plug and Play expansion board or other
option, such as a diskette drive.

■

Are all of the necessary device drivers installed?

■

Have all printer drivers been installed for each application?

■

Remove all bootable media (diskette, CD, or USB device) from the system before turning on
the system.

■

Are all switches set correctly?

■

Is the NIC Remote Wakeup cable (featured on some models) connected between the NIC and
the riser/system board?

«
...
183
184
185
186
187
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Brand: Acer Pages: 24

Brand: Acer Pages: 24

Brand: Production Basics Pages: 3

PS/2 N51 SX HMR

Brand: IBM Pages: 43

Brand: Commodore Pages: 31

Brand: Zotac Pages: 20

FocusPRO 6000 Series

Brand: Honeywell Pages: 64

X-Superteam XPS-100

Brand: Honeywell Pages: 40

Brand: Honeywell Pages: 69

Brand: Honeywell Pages: 39

Brand: Honeywell Pages: 78

Brand: Honeywell Pages: 39

Brand: Honeywell Pages: 133

Brand: Honeywell Pages: 159

Brand: Honeywell Pages: 180

Brand: Honeywell Pages: 198

Brand: PowerCenter Pages: 29

Brand: MSI Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands