manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

D–5

Solving Power Supply Problems

Solving Power Supply Problems 

Problem

Cause

Solution

Power supply shuts down 
intermittently.

Voltage selector switch 
on rear of computer 
chassis not switched to 
correct line voltage.

Select the proper AC voltage.

Power supply fault. 

Replace the power supply.

Computer powered off 
automatically and the 
Power LED flashes Red two 
times, once every second, 
followed by a two second 
pause, and the computer 
beeps two times. Beeps 
continue for five iterations 
after which the LED flashes 
will continue until the 
problem is resolved.

Processor thermal 
protection activated:
A fan may be blocked 
or not turning.
OR 
The heatsink/fan 
assembly is not properly 
attached to the 
processor.

1. Ensure that the computer air 

vents are not blocked and the 
cooling fan is running.

2. Open hood, press the power 

button, and see if the processor 
fan spins. If the processor fan is 
not spinning, make sure the 
fan's cable is plugged onto the 
system board header. Ensure 
the fan is fully/properly seated 
or installed.

3. Replace the processor fan.

4. Reseat processor heatsink and 

verify that the fan assembly is 
properly attached.

Power LED flashes Red, four 
times, once every second, 
followed by a two second 
pause, and the computer 
beeps four times. Beeps 
continue for five iterations 
after which the LED flashes 
will continue until the 
problem is resolved.

Power failure (power 
supply is overloaded).

1. Check that the voltage selector, 

is set to the appropriate voltage. 

2. Open the hood and ensure the 

4- or 6-wire power supply cable 
is seated into the connector on 
the system board.

3. Check if a device is causing the 

problem by removing ALL 
attached devices). Power on the 
system. If the system enters the 
POST, then power off and 
replace one device at a time 
and repeat this procedure until 
failure occurs. Replace the 
device causing the failure. 
Continue adding devices one at 
a time to ensure all devices are 
functioning properly.

4. Replace the power supply.

5. Replace the system board.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Safco 1901 Assembly Instructions preview
1901
Brand: Safco Pages: 2
DEC DECstation 316+ Service Manual preview
DECstation 316+
Brand: DEC Pages: 94
C&T Solution ACO-3000-4L-5350U User Manual preview
ACO-3000-4L-5350U
Brand: C&T Solution Pages: 97
Acer Altos BrainSphere P130 F7 User Manual preview
Altos BrainSphere P130 F7
Brand: Acer Pages: 40
Vecow EAC-5000 User Manual preview
EAC-5000
Brand: Vecow Pages: 65
Uplift Desk Height Adjustable Standing Desk 4-Leg Assembly Instructions Manual preview
Height Adjustable Standing Desk 4-Leg
Brand: Uplift Desk Pages: 7
Contec BX-951-DC series User Manual preview
BX-951-DC series
Brand: Contec Pages: 111
VS Cabling Sitting/Standing Workstation Assembly Instructions Manual preview
Cabling Sitting/Standing Workstation
Brand: VS Pages: 8
Toshiba Satellite L830 Maintenance Manual preview
Satellite L830
Brand: Toshiba Pages: 250
Sony PCV-RX370DS - Vaio Digital Studio Desktop Computer Specifications preview
PCV-RX370DS - Vaio Digital Studio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RX360DS - Vaio Digital Studio Desktop Computer Specifications preview
PCV-RX360DS - Vaio Digital Studio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RX260DS - Vaio Digital Studio Desktop Computer Specifications preview
PCV-RX260DS - Vaio Digital Studio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RS720G - Vaio Desktop Computer Specifications preview
PCV-RS720G - Vaio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RS710GX - Vaio Desktop Computer Specifications preview
PCV-RS710GX - Vaio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RX301 Specifications preview
PCV-RX301
Brand: Sony Pages: 8
Sony PCV-RS710G - Vaio Desktop Computer Specifications preview
PCV-RS710G - Vaio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RS700CG - Vaio Desktop Computer Specifications preview
PCV-RS700CG - Vaio Desktop Computer
Brand: Sony Pages: 1
Sony PCV-RS630G - Vaio Desktop Computer Specifications preview
PCV-RS630G - Vaio Desktop Computer
Brand: Sony Pages: 1

Brands by name

Popular brands

Load more brands