manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

C–8

376220-001

Service Reference Guide, dc5100

Red Power LED 
flashes three times, 
once every 
second, followed 
by a two second 
pause. Beeps stop 
after the fifth 
iteration but the 
LED continues to 
flash until the issue 
has been resolved.

3

Processor not 
installed (not an 
indicator of bad 
processor).

Check to see that the processor is present.
Reseat the processor.

Red Power LED 
flashes four times, 
once every 
second, followed 
by a two second 
pause. Beeps stop 
after the fifth 
iteration but the 
LED continues to 
flash until the issue 
has been resolved.

4

Power failure 
(power supply is 
overloaded).

Open the hood and ensure the power 
supply cable is seated into the connector 
on the system board.
Check if a device is causing the problem 
by removing ALL attached devices (such as 
hard, diskette, or optical drives, and 
expansion cards). Power on the system. If 
the system enters the POST, then power off 
and replace one device at a time and 
repeat this procedure until failure occurs. 
Replace the device that is causing the 
failure. Continue adding devices one at a 
time to ensure all devices are functioning 
properly.
Replace the power supply.
Replace the system board.

Red Power LED 
flashes five times, 
once every 
second, followed 
by a two second 
pause. Beeps stop 
after the fifth 
iteration but the 
LED continues to 
flash until the issue 
has been resolved.

5

Pre-video 
memory error.

Reseat DIMMs. Power on the system.
Replace DIMMs one at a time to isolate 
the faulty module.
Replace third-party memory with HP 
memory.
Replace the system board.

Activity

Beeps

Possible 

Cause

Recommended Action

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Xerox 8010 Hardware Reference Manual preview
8010
Brand: Xerox Pages: 20
TES IEC-22 User Manual preview
IEC-22
Brand: TES Pages: 45
IBM System x3200 M3 Product Manual preview
System x3200 M3
Brand: IBM Pages: 42
BTOD VERTDESK V3 Instruction preview
VERTDESK V3
Brand: BTOD Pages: 12
MSI 482 User Manual preview
482
Brand: MSI Pages: 100
Dell OptiPlex 380 Service Manual preview
OptiPlex 380
Brand: Dell Pages: 54
Casio FX-890P Owner'S Manual preview
FX-890P
Brand: Casio Pages: 126
Asus M32CD User Manual preview
M32CD
Brand: Asus Pages: 54
Asus GT51CH User Manual preview
GT51CH
Brand: Asus Pages: 48
Asus M70AD User Manual preview
M70AD
Brand: Asus Pages: 80
Asus M32BC User Manual preview
M32BC
Brand: Asus Pages: 66
Asus P5G31D-M PRO User Manual preview
P5G31D-M PRO
Brand: Asus Pages: 92
Asus GT51CA User Manual preview
GT51CA
Brand: Asus Pages: 48
Asus P2-P5N9300 User Manual preview
P2-P5N9300
Brand: Asus Pages: 82
Asus M80CJ User Manual preview
M80CJ
Brand: Asus Pages: 46
Asus P3-PH5 Installation Manual preview
P3-PH5
Brand: Asus Pages: 80
Asus M32 Series User Manual preview
M32 Series
Brand: Asus Pages: 81
Asus Multimedia System S-presso User Manual preview
Multimedia System S-presso
Brand: Asus Pages: 106

Brands by name

Popular brands

Load more brands