HP Compaq dc5100 Series Service & Reference Manual Download Page 207

Page: 207 / 230

Service Reference Guide, dc5100

376220-001

D–23

Diagnostics passes, but
the computer does not
communicate with the
network.

Network drivers are
not loaded, or driver
parameters do not match
current configuration.

1. Make sure the network drivers

are loaded and that the driver
parameters match the
configuration of the network
controller.

2. Make sure the correct network

client and protocol is installed.

Diagnostics passes, but
the computer does not
communicate with the
network. (continued)

The network controller
is not configured for this
computer.

Select the

Network

icon in the

Control Panel

and configure the

network controller.

Network controller
stopped working when
an expansion board was
added to the computer.

Network controller
interrupt is shared with an
expansion board.

Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

The network controller
requires drivers.

Verify that the drivers were not
accidentally deleted when the
drivers for a new expansion board
were installed.

The expansion board
installed is a network card
(NIC) and conflicts with
the embedded NIC.

Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

Network controller stops
working without apparent
cause.

The files containing the
network drivers are
corrupted.

Reinstall the network drivers, using
the

Restore Plus!

CD.

The cable is not securely
connected.

Ensure that both ends of the cable
are securely attached to the correct
devices.

The network controller is
defective.

Replace the NIC.

New network card will
not boot.

New network card may be
defective or may not meet
industry-standard
specifications.

Install a working, industry-standard
NIC, or change the boot sequence
to boot from another source.

Cannot connect to
network server when
attempting Remote
System Installation.

The network controller is
not configured properly.

Verify Network Connectivity, that a
DHCP Server is present, and that
the Remote System Installation
Server contains the NIC drivers for
your NIC.

System setup utility
reports unprogrammed
EEPROM.

Unprogrammed EEPROM.

Flash the ROM.

Solving Network Problems

(Continued)

Problem

Cause

Solution

Summary of Contents for Compaq dc5100 Series







































































































































































































































Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands

HP Compaq dc5100 Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands