manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

4–10

376220-001

Service Reference Guide, dc5100

Serial and Parallel ATA Drive Guidelines and Features

4.4  ATA SMART Drives

The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP 
Personal Computers have built-in drive failure prediction that warns the user or network 
administrator of an impending failure or crash of the hard drive. The SMART drive tracks fault 
prediction and failure indication parameters such as reallocated sector count, spin retry count, 
and calibration retry count. If the drive determines that a failure is imminent, it generates a fault 
alert.

4.5 Drive 

Capacities

The combination of the file system and the operating system used in the computer determines the 
maximum usable size of a drive partition. A drive partition is the largest segment of a drive that 
may be properly accessed by the operating system. A single hard drive may therefore be 
subdivided into a number of unique drive partitions in order to make use of all of its space. 

Because of the differences in the way that drive sizes are calculated, the size reported by the 
operating system may differ from that marked on the hard drive or listed in the computer 
specification. Drive size calculations by drive manufacturers are bytes to the base 10 while 
calculations by Microsoft are bytes to the base 2.

Drive/Partition Capacity Limits

Maximum Size

File 

System

Controller 

Type

Operating System

 

Partition Drive 

FAT 32

ATA

Windows 2000/ XP

32 GB

128 PB

FAT 32

SCSI

Windows 2000/ XP

32 GB

2 TB

NTFS

ATA

Windows NT/2000/XP

2 TB

128 PB

NTFS

SCSI

Windows NT/2000/XP

2 TB

2 TB

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Raven CR7 User Manual preview
CR7
Brand: Raven Pages: 34
Raven CR7 Installation Manual preview
CR7
Brand: Raven Pages: 8
Rousseau W31-SE19B Assembly Manual preview
W31-SE19B
Brand: Rousseau Pages: 7
Vecow ECS-9755-505MGTX950 User Manual preview
ECS-9755-505MGTX950
Brand: Vecow Pages: 111
WynMax WMBX-3011-2701 series User Manual preview
WMBX-3011-2701 series
Brand: WynMax Pages: 58
Advantech EPC-C301 Series User Manual preview
EPC-C301 Series
Brand: Advantech Pages: 80
RNG Kraus Group MICON 500C Installation Manual preview
Kraus Group MICON 500C
Brand: RNG Pages: 50
Android TV Cloud Stick Quick Start Manual preview
TV Cloud Stick
Brand: Android Pages: 7
Quanmax QutePC-2000 User Manual preview
QutePC-2000
Brand: Quanmax Pages: 34
Morrow Tricep Installation Manual preview
Tricep
Brand: Morrow Pages: 162
Oracle MICROS Compact Workstation 310 Quick Assembly Manual preview
MICROS Compact Workstation 310
Brand: Oracle Pages: 2
Epson ActionDesk 4000 Specifications preview
ActionDesk 4000
Brand: Epson Pages: 11
Epson ActionPC 7000 Product Information Manual preview
ActionPC 7000
Brand: Epson Pages: 10
Epson ActionTower 2000 User Manual preview
ActionTower 2000
Brand: Epson Pages: 131
Epson ActionPC 6000 User Manual preview
ActionPC 6000
Brand: Epson Pages: 144
Epson ActionPC 3000 User Manual preview
ActionPC 3000
Brand: Epson Pages: 131
Epson ActionPC 2000 User Manual preview
ActionPC 2000
Brand: Epson Pages: 129
Epson ActionPC 5500 User Manual preview
ActionPC 5500
Brand: Epson Pages: 147

Brands by name

Popular brands

Load more brands