manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

D–33

Red Power LED 
flashes ten times, 
once every second, 
followed by a two 
second pause and 
the computer beeps 
ten times. Beeps 
stop after fifth 
iteration but LEDs 
continue until 
problem is 
resolved.

10

Bad option card.

1. Check each option card (PCI or PCI 

Express) by removing the card (one at 
a time if multiple cards), then power 
on the system to see if fault goes 
away.

2. Once a bad card is identified, remove 

and replace the bad option card.

3. Replace the system board.

System does not 
power on and LEDs 
are not flashing.

None

System unable to 
power on.

Press and hold the power button for less 
than 4 seconds. If the hard drive LED turns 
green, then:

1. Check that the voltage selector, 

located on the rear of the power 
supply, is set to the appropriate 
voltage. Proper voltage setting 
depends on your region.

2. Remove the expansion cards one at a 

time until the LED light on the system 
board turns on.

3. Replace the system board.

OR
Press and hold the power button for less 
than 4 seconds. If the hard drive LED does 
not turn on green then:

1. Check that the unit is plugged into a 

working AC outlet.

2. Open hood and check that the power 

button harness is properly connected 
to the system board.

3. Check that both power supply cables 

are properly connected to the system 
board.

4. Check to see if the LED light on the 

system board is turned on. If it is 
turned on, then replace the power 
button harness.

5. If the LED light on the system board is 

not turned on, then replace the power 
supply.

6. Replace the system board.

Diagnostic Front Panel LEDs and Audible Codes 

(Continued)

Activity

Beeps

Possible Cause

Recommended Action

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM 5110 Basic Introduction preview
5110
Brand: IBM Pages: 170
IBM 5110 Maintenance Analysis Procedures preview
5110
Brand: IBM Pages: 257
IBM 5110 General Information And Physical Planning Manual preview
5110
Brand: IBM Pages: 63
Gateway E-420 Maintaining & Troubleshooting preview
E-420
Brand: Gateway Pages: 108
Gateway GT5062b User Manual preview
GT5062b
Brand: Gateway Pages: 96
Rousseau W31-SE19B Assembly Manual preview
W31-SE19B
Brand: Rousseau Pages: 7
Gateway Profile 6 User Manual preview
Profile 6
Brand: Gateway Pages: 176
Foxconn R10-S3 Manual preview
R10-S3
Brand: Foxconn Pages: 2
Dell Dimension XPS H233 Service Manual preview
Dimension XPS H233
Brand: Dell Pages: 89
Dell Dimension XPS R Series Service Manual preview
Dimension XPS R Series
Brand: Dell Pages: 94
Dell DIMENSION XPS GEN 3 WHL User Manual preview
DIMENSION XPS GEN 3 WHL
Brand: Dell Pages: 144
Dell Inspiron 14 5415 Setup And Specifications preview
Inspiron 14 5415
Brand: Dell Pages: 21
Dell Inspiron 1410 Service Manual preview
Inspiron 1410
Brand: Dell Pages: 35
Dell Inspiron 14 5410 Quick Start Manual preview
Inspiron 14 5410
Brand: Dell Pages: 14
Dell Inspiron 1546 Specifications preview
Inspiron 1546
Brand: Dell Pages: 8
Dell Inspiron 1470 Service Manual preview
Inspiron 1470
Brand: Dell Pages: 45
Dell Inspiron 20 Owner'S Manual preview
Inspiron 20
Brand: Dell Pages: 85
Dell Inspiron 1440 Service Manual preview
Inspiron 1440
Brand: Dell Pages: 47

Brands by name

Popular brands

Load more brands